ACUVANCE XARVIX XX Скачать руководство пользователя страница 12

Страница: 12 / 12

MEMO

Error signal during driving (LED flashing pattern)

When the ESC battery terminal voltage drops to the cut-off

voltage set on P.16, the standby LED lights up and flashes,

and the green LED will be flashed and drive speed is going

to low.

LED green blinks and runs at low speed ~ Low voltage cut-off

Protection circuit for Battery reverse connection

This product is equipped with a reverse battery protection

circuit, so the ESC circuit is protected if the reverse

connection less than about 10 seconds. (Some heat is

generated when the protection circuit is activated.)

When the battery is connected in reverse, the LED on the

back of the battery terminal will turn red. Remove the

battery immediately and reconnect it correctly.

※

The protection circuit is automatically activated

when the battery is reversely connected.

When the ESC overheats due to driving and reaches the

specified temperature, the orange LED blinks in addition to

the standby LED lighting / flashing, and the vehicle runs at

low speed.

In this case, stop driving until the ESC temperature drops.

If the heat protection is activated in a short driving time, the gear ratio setting may be

overloaded. In this case, check each setting status.

LED orange blinks and runs at low speed

〜

Heat protection

Important

The condition to detect the cut-off voltage is not “Battery voltage” but “ESC battery

terminal voltage”. If the contact condition of the connector to which the battery is

connected and the welded state of the solder bonding the connector are

insufficient, that portion will have a large electrical resistance, and the voltage

detected at the ESC terminal will be far below the battery voltage.

If there is a large difference between the set cut-off voltage and the actual battery

voltage at the time of cut-off operation, the reason may be due to the connector to

which the battery is connected or the solder welding location of the connector.

In such cases, the ESC or motor performance may not be fully achieved. It is

recommended to replace the connector or rework the solder.

Important

This function protects only the ESC circuit board when the battery is reversely

connected. Capacitors connected to ESC such as Chevalier series are not

protected, so be careful when connecting batteries.

Green LED blinking

Orange LED blinking

Alert red LED light

Содержание XARVIX XX













Результаты поиска

Содержание XARVIX XX

Отзывы:

Похожие инструкции для XARVIX XX

Бренды по названию

Популярные бренды

ACUVANCE XARVIX XX, Руководство пользователя

Результаты поиска

Содержание XARVIX XX

Отзывы:

Похожие инструкции для XARVIX XX

Бренды по названию

Популярные бренды