Acuity Brands Lighting AARP страница 9 Скачать руководство пользователя

Страница: 9 / 18

Installation Instructions

RSX LED

Lithonia Lighting Outdoor

One Lithonia Way, Conyers, GA 30012

Phone: 800-279-8041 Fax: 770-918-1209

www.lithonia.com

Part Number: IM-459 Rev A

Revision Date: 8/29/19

8. Reorient luminaire to desired position on the tenon and Insert provided 7/16"-14 x 4-1/2" bolt through Mast Arm Mount
and drilled 1/2" Ø hole on tenon and place provided 7/16" nut onto bolt (see figure 12) and tighten securely to 45-50 ft-lbs.

9. Evenly tighten the Six (6) 3/8-16 UNC Mast Arm Set Bolts while maintaining the correct position of the luminaire to 23-27
ft-lbs.

10. Energize the luminaire to verify its operation and proper illumination of area.

WARNING: USE AND PROPERLY TIGHTEN THRU-BOLT AND NUT. FAILURE TO CORRECTLY INSTALL COULD RESULT IN SERIOUS

INJURY OR PROPERTY DAMAGE

Page #7

Содержание AARP



















Результаты поиска

Содержание AARP

Отзывы:

Похожие инструкции для AARP

Бренды по названию

Популярные бренды

Acuity Brands Lighting AARP, Руководство пользователя

Результаты поиска

Содержание AARP

Отзывы:

Похожие инструкции для AARP

Бренды по названию

Популярные бренды