manualshive.com logo in svg

Actron Code Scanner CP9015, Инструкция по эксплуатации, Страница: 50 / 66

Поделиться
Скачать
Actron Code Scanner CP9015 Скачать руководство пользователя страница 50

50

V-6:

 Mid Vacuum Switch

circuit is always open.

V-8:

 Mid Vacuum Switch

circuit is always open.

56

I-6:

 Closed Throttle

Vacuum Switch circuit is
always open.

61

V-6:

 Hi/Low Vacuum

Switch circuit is always
closed.

V-8:

 Hi/Low Vacuum

Switch circuit is always
closed.

62

Note:

 “High Altitude”

refers to vehicles with
computer adjusted for
operation at high elevations
such as in Denver,
Colorado.

I-4 

(car): Idle Tracking

Switch (ITS) circuit is
closed at idle.

I-4 

(truck): Idle/Decel

Vacuum Switch circuit is
always closed.

I-6:

 Wide Open Throttle

(WOT) Vacuum Switch
circuit is always closed.

V-6 

(All except High Altitude):

Altitude (ALT) circuit is
open.

V-6 

(High Altitude only):

System pass.

V-8 

(All except High

Altitude): Altitude (ALT)

circuit is open.

V-8 

(High Altitude only):

System pass.

63

I-4:

 Wide Open Throttle

(WOT) Vacuum Switch
circuit is always closed.

I-6:

 CROWD Vacuum

Switch circuit is always
closed.

65

Note:

 “High Altitude” refers

to vehicles with computer
adjusted for operation at
high elevations such as in
Denver, Colorado.

I-4 

(All except High Altitude):

Altitude (ALT) circuit is
open.

I-4 

(High Altitude only):

System pass.

V-6:

 

Mid Vacuum Switch

circuit is always closed.

V-8:

 

Mid Vacuum Switch

circuit is always closed.

66

I-6:

 Closed Throttle

Vacuum Switch circuit is
always closed.

Содержание Code Scanner CP9015



































































Отзывы:

Нет отзывов