manualshive.com logo in svg

Actron Code Scanner CP9015, Инструкция по эксплуатации, Страница: 44 / 66

Поделиться
Скачать
Actron Code Scanner CP9015 Скачать руководство пользователя страница 44

44

• Have your vehicle professionally

serviced. Codes indicate problems
found by the computer.

or,

• Repair the vehicle yourself using

service codes to help pinpoint the
problem. Refer to Test Results
Chart.

Key On Engine Off (KOEO) Test Results

KOEO

CODES

ACTION TO TAKE:

11*

System pass. No problem found by computer during KOEO Self-

(all except

Test. Go to SELF-TEST PART 3: Key On Engine Running

high altitude)

(KOER) Self-Test.

62*

System pass. No problem found by computer during KOEO Self-

(high altitude V-6

Test. Go to SELF-TEST PART 3: Key On Engine Running

or V-8 ONLY)

(KOER) Self-Test.

65*

System pass. No problem found by computer during KOEO Self-

(high altitude

Test. Go to SELF-TEST PART 3: Key On Engine Running

I-4 ONLY)

(KOER) Self-Test.

Any Code(s)

Codes indicate system problems are present now. Write down all
codes. Refer to vehicle service manual for code troubleshooting
charts and repair procedures. Repeat PART 2:  Key On Engine
Off (KOEO) Self-Test after every repair. Do not proceed to SELF-
TEST PART 3 until a system pass code is received.

No Codes

You have a problem which must be repaired before proceeding.

Received

Refer to the vehicle service manual “Self-Test Not Functional” (or

(STO light

similar title) troubleshooting chart.

always

on or off)

*Note:  “High Altitude” refers to vehicles with computer adjusted for operation at high
elevations such as in Denver, Colorado.

Содержание Code Scanner CP9015



































































Отзывы:

Нет отзывов