Actron Code Scanner CP9015 Скачать руководство пользователя

Страница: 43 / 66

Self-Test Part 2:

Key On Engine Off (KOEO) Self-Test.

IMPORTANT: You must complete all steps in Self-Test Part 1

before proceeding to Part 2.

1) Verify:

Ignition Key is in OFF Position and
Code Scanner is Connected.

2) Put Code Scanner HOLD/TEST

Switch in TEST Position.

• Optional: Turn the AUDIO switch ON to

hear “beeps” when the codes are sent.

3) Turn Ignition Key to ON Position but

DO NOT START THE ENGINE.

• This starts the KOEO Self-Test.

• Codes are sent after 5 seconds.

• Pay no attention to a brief blink which

may occur after ignition key is turned
to ON position.

4) Get Codes from the Flashing STO

Light.

Note: If the light does not flash, go
back and repeat SELF-TEST PART 2
starting with Step 1.

If the light still does not flash, you have
a problem which must be repaired
before proceeding. Refer to the vehicle
service manual “Self-Test Not
Functional” (or similar title) trouble-
shooting chart.

• Count flashes to get service codes.

(Each flash lasts 1/2 second.)

Code 12 looks like:

❊

PAUSE

❊❊

FLASH (pause) FLASH FLASH

(FLASH = 1, FLASH FLASH = 2.

(Put 1 and 2 together = code 12.)

Code 23 looks like:

❊❊

PAUSE

❊❊❊

FLASH FLASH (pause)

FLASH FLASH FLASH

• All codes are 2 digits long.

• The pause between each digit is 2

seconds.

• After all codes are sent, the whole

group is sent again just one more
time (so you can double check your
code list).

• The longer pause between each

code is 4 seconds.

Example of code 12 only:

❊

PAUSE

❊❊

FLASH (pause) FLASH FLASH

(longer pause)

❊

PAUSE

❊❊

FLASH (pause) FLASH FLASH

Example of code series 12 and 42:

❊

PAUSE

❊❊

FLASH (pause) FLASH FLASH

(longer pause)

❊❊❊❊

PAUSE

❊❊

FLASH FLASH FLASH FLASH (pause)

FLASH FLASH

(longer pause)

❊

PAUSE

❊❊

FLASH (pause) FLASH FLASH

(longer pause)

❊❊❊❊

PAUSE

❊❊

FLASH FLASH FLASH FLASH (pause)

FLASH FLASH

5) Turn Ignition Key to OFF Position.

At this point you can either:

Содержание Code Scanner CP9015



































































Результаты поиска

Содержание Code Scanner CP9015

Отзывы:

Похожие инструкции для Code Scanner CP9015

Бренды по названию

Популярные бренды

Actron Code Scanner CP9015, Инструкция по эксплуатации

Результаты поиска

Содержание Code Scanner CP9015

Отзывы:

Похожие инструкции для Code Scanner CP9015

Бренды по названию

Популярные бренды