Active Technologies AT-1212 Скачать руководство пользователя

Страница: 7 / 41

AT-1212 User Guide and Specifications - 7 -

www.activetechnologies.it

Front Panel and Connector Pinouts

Table 2 shows the front panel connectors and signal descriptions for AT-1212. Refer to the

Specifications

sheet for additional signal information.

Caution

To avoid permanent damage to the AT-1212, disconnect all signals connected to the AT-1212

before powering down the module, and connect signals only after the adapter module has been
powered on by the NI FlexRIO FPGA module.

Device Front Panel

Connector

Signal Description

TRIG IN

SMA input connector for Trigger IN

TRIG OUT

SMA output connector for Trigger Out

AO 1+

Differential analog channel 1

AO 1-

Differential analog output- channel 1

AO 0+

Differential analog channel 0

AO 0-

Differential analog output- channel 0

CLK IN

SMA input connector for external clock

When using single-ended output, terminate the unused output

with a 50 Ω

terminator.

Содержание AT-1212










































Результаты поиска

Содержание AT-1212

Отзывы:

Похожие инструкции для AT-1212

Бренды по названию

Популярные бренды

Active Technologies AT-1212, Руководство пользователя

Результаты поиска

Содержание AT-1212

Отзывы:

Похожие инструкции для AT-1212

Бренды по названию

Популярные бренды