Acromag IP445 Series, Руководство пользователя

Страница: 3 / 21

SERIES IP445 INDUSTRIAL I/O PACK 32 CHANNEL ISOLATED SSR OUTPUT MODULE
___________________________________________________________________________________________
- 2 -
The information contained in this manual is subject to change
without notice. Acromag, Inc. makes no warranty of any kind with
regard to this material, including, but not limited to, the implied
warranties of merchantability and fitness for a particular purpose.
Further, Acromag, Inc. assumes no responsibility for any errors that
may appear in this manual and makes no commitment to update, or
keep current, the information contained in this manual. No part of
this manual may be copied or reproduced in any form, without the
prior written consent of Acromag, Inc.
Table of Contents Page
1.0 GENERAL INFORMATION...............................................
2
KEY IP445 FEATURES..................................................... 2
INDUSTRIAL I/O PACK INTERFACE FEATURES.......... 3
SIGNAL INTERFACE PRODUCTS.................................. 3
INDUSTRIAL I/O PACK SOFTWARE LIBRARY.............. 3
2.0 PREPARATION FOR USE................................................ 3
UNPACKING AND INSPECTION..................................... 3
CARD CAGE CONSIDERATIONS................................... 4
BOARD CONFIGURATION.............................................. 4
CONNECTORS................................................................. 4
IP Field I/O Connector (P2)............................................ 4
Grounding and Noise Considerations............................. 5
IP Logic Interface Connector (P1).................................. 5
3.0 PROGRAMMING INFORMATION.................................... 5
IP IDENTIFICATION ROM................................................ 5
I/O SPACE ADDRESS MAP............................................. 6
REGISTER DEFINITIONS................................................ 6
Control Register............................................................. 6
Port Output Registers.................................................... 6
IP445 PROGRAMMING.................................................... 6
4.0 THEORY OF OPERATION............................................... 7
LOGIC/POWER INTERFACE........................................... 7
OUTPUT PORTS.............................................................. 7
5.0 SERVICE AND REPAIR.................................................... 7
SERVICE AND REPAIR ASSISTANCE........................... 7
PRELIMINARY SERVICE PROCEDURE......................... 7
6.0 SPECIFICATIONS............................................................. 8
GENERAL SPECIFICATIONS.......................................... 8
DIGITAL SSR OUTPUTS................................................. 8
INDUSTRIAL I/O PACK COMPLIANCE........................... 8
APPENDIX......................................................................... 9
CABLE: MODEL 5025-550 & 5025-551............................ 9
CABLE: MODEL 5029-900................................................ 9
TERMINATION PANEL: MODEL 5025-552..................... 9
TERMINATION PANEL: MODEL 5029-910..................... 9
TRANSITION MODULE: MODEL TRANS-GP................. 10
DRAWINGS Page
4501-434 IP MECHANICAL ASSEMBLY.........................
11
4501-606 IP445 RESISTOR LOCATION DRAWING...... 11
4501-604 IP445 FIELD CONNECTIONS......................... 12
4501-603 IP440/445 LOOPBACK CONNECTIONS........
13
4501-605 IP445 BLOCK DIAGRAM.................................
14
4501-462 CABLE 5025-550 (NON-SHIELDED).............. 15
4501-463 CABLE 5025-551 (SHIELDED)........................ 15
4501-464 TERMINATION PANEL 5025-552................... 16
4501-465 TRANSITION MODULE TRANS-GP............... 16
IMPORTANT SAFETY CONSIDERATIONS
It is very important for the user to consider the possible adverse
effects of power, wiring, component, sensor, or software failures in
designing any type of control or monitoring system. This is
especially important where economic property loss or human life is
involved. It is important that the user employ satisfactory overall
system design. It is agreed between the Buyer and Acromag, that
this is the Buyer's responsibility.
1.0 GENERAL INFORMATION
The Industrial I/O Pack (IP) Series IP445 module is a bus
isolated 32-channel output module. The IP445 provides control for
32 solid state relays which are bipolar and may be used to switch
positive or negative voltages. Four units may be mounted on a
carrier board to provide up to 128 channels of output control in a
single system slot. The IP445 offers a variety of features which
make it an ideal choice for many industrial and scientific applications
as described below.
MODEL OPERATING TEMPERATURE RANGE
IP445 0 to +70
°
C
IP445E -40 to +85
°
C
KEY IP445 FEATURES
•
High Channel Count - Individual control of up to 32 (SPST-
NO) bipolar Solid State Relays (SSR’s) is provided. Four units
mounted on a carrier board provide 128 channels in a single
system slot.
•
High-Speed/0 Wait States - No wait states are required for all
read/write cycles (all cycles complete in 250nS.) and hold
states are supported.
•
Optically Isolated - Individual bipolar SSR’s provide isolation.
The IP445 contains four groups (ports) of eight channels which
include separate port commons to ensure port to port isolation.
Individual ports are isolated from each other and from the IP
logic.
•
Low-Side or High-Side Switch Configuration - Each group
of eight channels can be connected directly to positive or
negative supplies for high (hot) side switching. Alternatively,
each group of eight channels can be connected to common for
low side switching. Socketed pull-up resistors are provided for
low side switching applications.
•
TTL Compatible - When configured as a low side switch will
sink 27mA at 0.4 volts. Sourcing is controlled by the installed
pull-up resistor.
•
Power Up & System Reset is Fail-safe - For safety, the
outputs are turned OFF upon power-up and a system reset.
Thus, the SSR’s will be disabled after a power-up or system
reset.
•
Wide Range Bipolar Voltage Outputs - Outputs are rated
from 0 to
±
60 volts. The bipolar solid state relays allow both
AC and DC switching.
•
Output Readback Function - Readback buffers are provided
that allow the output channel registers to be read back.
•
Loopback Compatible with IP440 Digital Input Module -
The P2 field I/O pin assignments of the IP445 output module
correspond with those of the Acromag IP440 Bus Isolated
Input module. This provides direct closed-loop monitoring of
the output states.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com