Acromag APCe7010E-LF Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 23

Acromag APCe7010E-LF Скачать руководство пользователя страница 7

AcroPack Series APCe7010E-LF

PCI Express Carrier Board

- 7 -

2.

PREPARATION FOR USE

IMPORTANT PERSONAL AND PRODUCT SAFETY CONSIDERATIONS

It is very important for the user to consider the possible safety implications of
power, wiring, component, sensor, or software failures in designing any type
of control or monitoring system. This is especially important where personal
injury or the loss of economic property or human life is possible. It is
important that the user employ satisfactory overall system design. It is
understood and agreed by the Buyer and Acromag that this is the Buyer's
responsibility.

WARNING: This board utilizes static sensitive components and should only
be handled at a static-safe workstation.

This product is an electrostatic

sensitive device and is packaged accordingly. Do not open or handle this
product except at an electrostatic-free workstation. Additionally, do not ship
or store this product near strong electrostatic, electromagnetic, magnetic, or
radioactive fields unless the device is contained within its original
manufacturer’s packaging. Be aware that failure to comply with these
guidelines will void the Acromag Limited Warranty.

UNPACKING AND INSPECTION

Upon receipt of this product, inspect the shipping carton for evidence of
mishandling during transit. If the shipping carton is badly damaged or water
stained, request that the carrier's agent be present when the carton is
opened. If the carrier's agent is absent when the carton is opened and the
contents of the carton are damaged, keep the carton and packing material for
the agent's inspection.

For repairs to a product damaged in shipment, refer to the Acromag Service
Policy to obtain return instructions. It is suggested that salvageable shipping
cartons and packing material be saved for future use in the event the product
must be shipped.

This board is physically protected with packing material and electrically
protected with an anti-static bag during shipment. It is recommended that the
board be visually inspected for evidence of mishandling prior to applying
power.

The board utilizes static sensitive components and should only be handled at
a static-safe workstation.

«
...
5
6
7
8
9
...
»

Содержание APCe7010E-LF
























Отзывы:

Нет отзывов