Acromag AcroPack AP513 Скачать руководство пользователя | Manualshive

Страница: 34 / 58

background image

AP513 ACROPACK

USER

’S MANUAL

Acromag, Inc. Tel: 248-295-0310

- 33 -

http://www.acromag.com

- 33 -

www.acromag.com

When software flow control in enabled, and one or two
sequential receive data characters match the
preprogrammed Xoff 1-2 values an interrupt will be issued.

6

1

RTS# Output Interrupt Enable:

0 = Disable RTS# interrupt (default).

1 = Enable RTS# interrupt.

This Interrupt is generated when the RTS pin transitions
from a logic 0 to a logic 1.

7

1

CTS# Input Interrupt Enable:

0 = Disable CTS# interrupt (default).

1 = Enable CTS# interrupt.

This interrupt will be issued when the CTS pin transitions
from a logic 0 to a logic 1.

1

Bits 5-7

are only programmable when the EFR bit 4 is set to “1”.

3.4.5 Interrupt Status Register (ISR)

–

Read Only

The Interrupt Status Register is used to indicate that a prioritized interrupt is
pending and the type of interrupt that is pending. Six levels of prioritized
interrupts are provided to minimize software interaction. Performing a read
cycle on the ISR will provide the user with the highest pending interrupt
level to be serviced. No other interrupts are acknowledged until the
pending interrupt is serviced. Whenever the interrupt status register is
read, the interrupt status is cleared.  Note, only the current pending
interrupt is cleared by the read.  A lower level interrupt may be seen after
re-reading the interrupt status bits.

The following interrupt source table shows the data values (bit 0-5) for the
six prioritized interrupt levels and the interrupt sources associated with each
of these interrupts.

«
...
32
33
34
35
36
...
»

Содержание AcroPack AP513



























































Отзывы:

Нет отзывов

Похожие инструкции для AcroPack AP513

Бренд: GE Страницы: 8

Бренд: MAKOT Страницы: 6

Total Access 351 Series

Бренд: ADTRAN Страницы: 4

Бренд: Sunlover Страницы: 2

Dynamic Boiler Controller

Бренд: Intiel Страницы: 25

THRUSTER COMMAND TCD 1022 E

Бренд: Quick Страницы: 56

AQUACULTURE AQC-A1-333-150

Бренд: Senect Страницы: 49

Бренд: Watt Stopper Страницы: 3

SANTOKA 12.1 BX PCT

Бренд: Garz & Fricke Страницы: 37

Бренд: QUANT Страницы: 24

Бренд: Festo Страницы: 60

Бренд: JASNO Страницы: 60

Бренд: SIMARINE Страницы: 22

Бренд: National Instruments Страницы: 7

Бренд: Daikin Страницы: 32

LIBRA LIB-P432EX

Бренд: NAPCO Страницы: 68

Ostrich Eggbot 2.0

Бренд: Evil Mad Scientist Страницы: 45

Бренд: Bartec Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды