manualshive.com logo in svg

Acromag AcroPack AP471 Series, Руководство пользователя

Поделиться
Скачать
Acromag AcroPack AP471 Series Скачать руководство пользователя страница 25

SERIES AP471 ACROPACK 

 

USER

’S MANUAL 

 

 

 

 

 

 

 

Acromag, Inc. Tel: 248-295-0310  

            - 23 -                                   

http://www.acromag.com  

- 23 - 

www.acromag.com 

 

points to 47. Bits 1-7 of this register are not used and will always read as 
zero. 

WARNING: IF USING I/O47 AS THE DEBOUNCE CLOCK, DO NOT SET THE I/O 
AS AN ACTIVE OUTPUT VIA THE CHANNEL I/O REGISTERS. SETTING I/O47 
AS AN ACTIVE OUTPUT MAY CAUSE A BUS CONFLICT. 

 

 

Bit(s) 

FUNCTION 

0 

Debounce Clock Select 

0 

Internal clock @ 31.25 MHz (default) 

1 

External clock on I/O47 

7 to 1 

Not Used 

 

 

Software Reset Register (Write Only)  

(BAR0 + 0x0000 006C)   

 

Writing a 1 to the bit 0 position of this register will cause a software reset to 
occur.  This bit is not stored and merely acts as a trigger for software reset 
generation (this bit will always read back as 0).  The Interrupt Enable Bit of 
the Interrupt Enable and Status register is not cleared in response to a 
software reset.  Bits 1-7 of this register are not used and will always read as 
zero. 

XADC Status/Control Register (Read/Write)  

(BAR0 + 0x0000 0070)   

This read/write register will access the XADC register at the address set in 
the XADC Address Register. This allows the board’s temperature and supply 
voltages to be read. 

For example, the address of the XADC Status register that is to be accessed 
is first set via the XADC Address register at BAR0 plus 0x74H.  Next, this 
register at BAR0 plus 0x70H is read.  Bits 22 to 16 of this register hold the 
address of the XADC register that is accessed.  Data bits 15 to 6 of this 
register hold the “ADCcode” temperature, Vccint, or Vccaux value.  Data bits 
5 to 0 are not used.  Valid addresses are given in column one of the table 
below. 

Reading or writing this register is possible via 32-bit data transfers. 

The 10-bits digitized and output from the ADC can be converted to 
temperature by using the following equation. 

15

.

273

1024

975

.

503

)

(

ADCcode

C

e

Temperatur

 

The 10-bits digitized and output from the ADC can be converted to voltage 
by using the following equation. 

V

ADCcode

volts

age

SupplyVolt

3

1024

)

(

 

Содержание AcroPack AP471 Series












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды