ACPC4610E/CC User’s Manual CompactPCI Bus PMC Carrier
___________________________________________________________________
__________________________________________________________________________
Acromag, Inc. Tel: 248-295-0310 Fax: 248-624-9234 Email:[email protected] http://www.acromag.com
3
The ACPC4610E/CC is a 3U CompactPCI Bus Non-Intelligent PMC
carrier board designed for the 32-bit 33MHz or 66MHz CompactPCI bus.
The carrier card uses a PLX Technology
R
Bridge Chip (PCI6540) to interface
between the CompactPCI bus and one PMC mezzanine I/O module card.
Model ACPC4610E is an air-cooled extended temperature product which
can be used for front and rear PMC mezzanine I/O modules. Front I/O can
be accessed through the front panel. Rear I/O can be accessed though the
J2 connector on the carrier.
•
ESD Strip on ACPC4610E Board
- The ACPC4610E board has been
designed to provide electrostatic discharge (ESD) capability by using an
ESD strip on the board per IEEE1101.10.
•
Injector/Ejector Handle
- The ACPC4610E uses a modern
injector/ejector handle, which pushes the board into the rack during
installation and has a positive self-locking mechanism so it cannot be
unlocked accidentally. This handle is fully IEEE 1101.10 compliant and
is needed to give leverage to install and remove the board.
•
EMC Front Panel
- The ACPC4610E uses the preferred EMC front
panel per IEEE 1101.10 specification.
Model ACPC4610CC is a conduction cooled product which is usually
only used for rear Conduction Cooled PMC mezzanine I/O modules. Rear
I/O can be accessed though the J2 connector on the carrier.
•
Conduction Cooled Frame
- The ACPC4610CC board has a custom
conduction cooled assembly consisting of a conduction cooled frame,
thermo bars, ejector/injectors and Wedge-Loks
R
designed to thermally
conduct heat away from the Conduction Cooled PMC modules per
ANSI/VITA 30.1-2001.
Model TRANS-C4610 Transition Module: This module plugs into the
rear backplane directly behind the ACPC4610E carrier board. The field I/O
connections are made through the backplane to the J2 connector of the
carrier board and then routed to a 68 pin SCSI-3 connector P1, on the
transition module, for rear exit from the card cage. This module is available
for use in card cages which provide rear exit for I/O connections via 80 mm
wide transition modules (transition modules can only be used in card cages
specifically designed for them). It is a single-height (3U), single-slot module
and adheres to the CompactPCI mechanical dimensions and IEEE Standard
(1101.11-1998), with a printed circuit board depth of 80mm, which is a
standard transition module depth. The transition module connects to
Acromag Termination Panel (Model 5025-288) using a round 68 conductor
shielded cable (Model 5028-432) to the rear of the card cage, and to the
ACPC4610E board within the card cage.
Model TRANS-C5210 Transition Module: Same as TRANS-C4610,
except I/O signals routed as differential pairs for the FPGA PMC Modules.
Model 5028-432: A 2-meter cable, with a male SCSI-3 connector at both
ends and 34 twisted pairs. This cable is used for connecting the TRANS-
C4610/-C5210 board to Model 5025-288 termination panels.
Model 5025-288: DIN-rail mountable panel provides 68 screw terminals
for universal field I/O termination. Connects to the TRANS-C4610/-C5210
board, via SCSI-3 to twisted pair cable, Model 5028-432.
1.0 GENERAL
INFORMATION
MODEL ACPC4610E
KEY FEATURES
MODEL ACPC4610CC
KEY FEATURES
CompactPCI Transition
Module
SIGNAL INTERFACE
PRODUCTS
Cables
Termination Panel
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
