INSTRUCTION MANUAL FOR DISHWASHERS
Page 10 of 12
GB
1
2
3
1
2
3
Chap 7
ADVANCED SETTINGS
The following adjustments should only be performed by a qualified technician.
O
PERATING TEMPERATURE
To access the temperature setting menu, press and hold the
ON/OFF (1)
button for a few seconds,
until the following menu appears:
A
BOILER SET
Rinse temperature adjustment
B
TANK SET
Tank temperature adjustment
To move from one command to the next, press the
ON/OFF (1)
button; to increase or decrease the parameters, press the
CYCLE
SELECTION (2)
and
START (3)
buttons. To exit the menu, press and hold the
ON/OFF (1) button for a few seconds.
P
ARAMETERS
To access the settings menu, proceed as follows:
•
While the machine is switched off, open the door
•
Press and hold the
CYCLE SELECTION (2)
and
START (3)
buttons simultaneously for a few
seconds
•
To move from one command to the next, press the
ON/OFF (1)
button; to increase or decrease
the parameters, press buttons
2
and
3
. To exit the menu, press and hold the
ON/OFF (1)
button.
A
LANGUAGE
Changes the language in which user messages are displayed.
B
THERMO-STOP
Enables or disables the
Thermostop function.
C
ENERGY SAVING
Enables or disables the
Energy saving function.
D
PREHEATING
Enables or disables the
Preheating
function (fast machine heating).
E
DETERGENT PUMP
Enables the detergent pump continuously. Press and hold button 3 to enable the detergent pump so
that its circuit can be loaded.
F
RINSE AID PUMP
Enables the rinse aid pump continuously. Press and hold button 3 to enable the rinse pump so that its
circuit can be loaded.
G
RINSE PUMP
Manual operation of the rinse pump.
H
DOSAGE TIME
DURING WASHING
Detergent pump operating time. Buttons 2 and 3 can be used to increase or decrease the dosage time.
I
RINSE PRODUCT
DOSAGE TIME
Rinse aid pump operating time. Buttons 2 and 3 can be used to increase or decrease the dosage time.
J
DRAIN PUMP
Enable drain pump (*optional).
K
WATER HARDNESS
(Machines with built-in softener only)
Set the
mains water hardness level in accordance with
the table below:
Measured
hardness
Water hardness
DF
DH
no.
0
÷
20
0
÷
11
1
21
÷
30
12
÷
16
2
31
÷
40
17
÷
22
3
41
÷
60
23
÷
33
4
61
÷
70
34
÷
42
5
L
CYCLES FOR
REGENERATION
ALARM WITH
EXTERNAL
SOFTENER
If an external softener is installed, it is possible to enter the number of cycles run before the machine
displays a request for maintenance. When the number of cycles has elapsed, the machine will display
the message “
SOFTENER MAINTENANCE
”. To remove this alert, press and hold the
START (3)
button while the door is open.
M
BUZZER
Enable buzzer.
N
CYCLE COUNTER
Indicates the number of cycles performed by the machine.
Содержание 915224
