ACIQ ACiQ-12FM-HH-MB Скачать руководство пользователя страница 7

Страница: 7 / 38



Page



Unit Specifications and Features

Unit

Specifications

and Featur

Indoor unit display

NOTE:

This display panel on the indoor unit can be used to operate the unit in case the remote control

has been misplaced or is out of batteries.

Drain hose

Refrigerant

connecting

pipe

Display panel

Air inlet (with air filter in it)

Air flow louver (at air outlet)

Display panel

MANUAL button:

This button selects the mode

in the following order: AUTO, FORCED COOL, OFF.

FORCED COOL mode:

In FORCED COOL mode,

the Operation light flashes. The system will then

turn to AUTO after it has cooled with a high wind

speed for 30 minutes. The remote control will be

disabled during this operation.

OFF mode:

The unit turns off and the remote

control is re-enabled.

Infrared receiver

Timer indicator
PRE-DEF

(pre-heating/defrost)

indicator

Operation indicator

Manual button

Infrared receiver

Operation indicator
Manual button

(A)

(B)

•

Displays temperature and Error codes:

“ ” when defrosting(for model B cooling &

heating units)

“ ” for 3 seconds when:

•

TIMER ON is set(for model B)

•

SWING or SILENCE is turned on

“ ” for 3 seconds when:

•

TIMER OFF is set(for model B)

•

SWING or SILENCE is turned off

“ ” when unit is self-cleaning

“ ” when 8 C heating feature is turned on

Содержание ACiQ-12FM-HH-MB







































Результаты поиска

Содержание ACiQ-12FM-HH-MB

Отзывы:

Похожие инструкции для ACiQ-12FM-HH-MB

Бренды по названию

Популярные бренды

ACIQ ACiQ-12FM-HH-MB, Руководство пользователя и инструкция по установке

Результаты поиска

Содержание ACiQ-12FM-HH-MB

Отзывы:

Похожие инструкции для ACiQ-12FM-HH-MB

Бренды по названию

Популярные бренды