background image

10

SAFETY INFORMATION

• 

Always ensure hooks and latches fully engage side rails.

• 

Ensure safety straps are attached to side rails when cover is installed.

• 

Ensure anchors are clear, free of interference.

• 

Never rest cover against cab after installation.

• 

Do not tow vehicle backward with cover on your truck.

• 

Do not cover cargo that is higher than the cover.

• 

Do not place object(s) on or against the cover or its framework at any time.

• 

Always secure cargo to ensure it does not damage cover or framework.

• 

Remove debris, snow or ice from cover and hinges before opening or closing cover.

• 

Do not use the cover’s framework to tie down cargo.

• 

Never stand, sit or ride on the cover or allow others to do so.

• 

Cover does not eliminate moisture and dust from entering the truck box. Special 
wrappings or packaging of the cargo may be necessary.

• 

Due to poor ventilation, if you allow a pet/animal in the box, leave cover open. Do not 
allow people or animals to occupy box with the cover closed.

• 

Avoid excessive speeds and high winds when cover is in vertical position.

• 

Do not clean cover with a pressure washer.

• 

Keep cover completely closed or in approved horizontal or vertical position. Do not  
drive with only the rear panel open.

• 

Before entering low clearance areas, check height restrictions to ensure safe entry.

• 

Keep cover closed when going through automatic car washes.

• 

Keep hands and fingers away from all pinch points.

• 

Never use latch cord to lift or fold cover.

• 

Use caution when operating cover in windy conditions.

INSPECTION AND MAINTENANCE

The operator can perform most of inspection and maintenance. It may be necessary to 

review the installation and operating instructions.

• 

Periodically check and retighten safety strap hardware. If safety straps are damaged, 

replace with new hardware.

• 

Periodically check and retighten clamps as needed.

• 

Periodically check latch cords to ensure latches fully engage side rails.

• 

Periodically inspect cover assembly and the condition of all parts. Check for loose 

bolts and parts, tighten if needed. Test the operation to ensure parts are functioning 

properly and cover is in top operational condition.

• 

If latches have been damaged, replace with new ones.

• 

Periodically ensure anchors are clear, free of interference. If anchors have been 

damaged, replace with new ones.

NOTE:

 Inspection and maintenance should also be performed anytime a malfunction 

is observed or suspected. If you need assistance inspecting or servicing your cover, or 

if you want to order a replacement part, call the customer service number on the back 

page. Always use original equipment replacement parts for your cover.

Содержание Lomax Stance Hard Cover













Отзывы: