SHIFT WARNING RPM OPERATION
1. Press MODE button to the RPM screen; pull on the throttle
until the desired shift warning RPM.
2. Press RESET button to confirm and set up the shift warning RPM.
3. Bar-graphic tachometer and warning LED will flash to warning
you shift gear.
4. Press RESET button for 2 seconds at the RPM screen to re-adjust
the shift warning RPM.
Backlight of Internal/Bike’s Powers:
1. The computer built-in a CR2032 battery for off road bikes in
case take away bike’s batter to reduce weight.
2. You can use both internal battery and bike’s battery at the
same time.
3. The backlight is always turned on if you connect to bike’s battery.
4. E
ach press of either button turn
s
on backlight for 3 seconds then
turn off automatically when uses CR2032 only.
BUTTON OPERATIONS
MODE BUTTON
Press the MODE button to move all functions in loop sequence
from one function screen to another.
RESET BUTTON
1. Press MODE button to get to the desired screen then press RESET
button for 2 seconds to reset hour meter, MAX thermometer*,
and MAX RPM data from stored values to zero individually.
2. TT data cannot be reset.
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
MAX C or F : Maximum Thermometer*
Displays highest temperature achieved after last Reset operation.
Volt: Digital Voltage Gauge*
It checks bike’s battery and charging systems health.
Fuel Gauge
1. Has 7 bars to indicate how much fuel remains.
2. Built-in 100, 250, 510Ohm, oFF, -100, -250 and -510 Ohm
fuel sender resistance, the fuel bars will disappear when
you select “oFF” mode.
3. The full bars are low resistance and empty bar is high
resistance for 100, 250 and 510ohm; -100, -250 and -510
ohm are the inverse.
4. Last bar flashes to indicate low fuel level automatically.
Bars
-250Ω
-100Ω
510Ω
250Ω
100Ω
7
6
5
4
3
2
1
0-Flash
0-10
11-20
21-35
36-45
46-60
61-75
76-90
91-100
0-25
26-50
51-85
86-110
111-150
151-200
201-230
231-250
0-50
51-100
101-180
181-230
231-300
301-380
381-460
461-510
100-90
89-75
74-60
59-45
44-35
34-20
19-10
9-0
250-230
229-200
199-150
149-110
109-85
84-50
49-25
24-0
-510Ω
510-460
459-380
379-300
299-230
229-180
179-100
99-50
49-0
RT1 or RT2: Maintenance Reminders
1.
It has 2 maintenance reminders RT1 and RT2, which count
down the preset entered time RT1 & RT2 since last RESET.
2. It accumulates RT1&RT2 when the count down reaches to
“0 ”, and symbols of “ RT1 or RT2” flash to remind you to
maintain oil or parts.
3. Push and hold RESET button to reset and restart the
maintenance reminder after changing oil or parts.
AUTO Power Off :
1. The power will be turned off automatically after 3 minutes the
unit does not receive any signal from speed, RPM or button
operation in case it is using the internal battery CR2032.
2. The riding data will be kept in memory at each power off before
the low battery icon appears.
3. The power is always turned on at LAP mode until go out the LAP
mode.
:Low Battery Indicator
1. The “ “ icon flashes when the CR-2032 battery is at low power
status to reminder you change the battery.
2. All setting is kept in memory not mater the power is connected to
bike’s 12VDC battery or using internal CR2032 battery only; In case
the power is only the internal CR2032 battery, the unit can display
riding data but can’t be kept in memory when the low battery icon
appears in order to avoid setting data be reset at low voltage, that
means riding data from last memory until the“ “ con appears is
lost.
3. Remove the old battery. Replace with a new CR2032 with the positive
(+) pole towards the battery cap.
4. Be sure to press RESET button at the rear side after installed the
battery to sure all functions work smoothly.
