![background image](http://html1.mh-extra.com/html/acer/veriton-m6618g/veriton-m6618g_service-manual_4693302027.webp)
Chapter 2
19
Integrated Peripherals
Parameter
Description
Option
Onboard SATA Controller
Enables or disables the onboard SATA controller.
Enabled
Disabled
Onboard SATA Mode
Select an operating mode for the onboard SATA.
Native IDE
RAID
AHCI
Onboard USB Controller
Enables or disables the onboard USB controller.
Enabled
Disabled
Legacy USB Support
Enables or disables support for legacy USB devices.
Enabled
Disabled
USB Storage Emulation
If Auto, USB device equal or less than 2GB will be emulated as Floppy
and remaining as harddrive. Forced FDD option can be used to force a
HDD formatted drive to boot as FDD (Ex.ZIP drive).
Auto
Floppy
Hard Disk
Onboard Graphics
Controller
This item allows you to enable or disable the onboard controller.
Enabled
Disabled
Onboard Audio Controller
Enables or disables the onboard audio controller.
Enabled
Disabled
Onboard LAN Controller
Enables or disables the onboard LAN controller.
Enabled
Disabled
Onboard LAN Option ROM
Enables or disables the load of embedded option ROM for onboard
network controller.
Enabled
Disabled
Serial Port1 Address
Use this item to enable or disable the onboard COM1 serial port, and to
assign a portaddress.
Disabled
3F8/IRQ4
2F8/IRQ3
3E8/IRQ4
2E8/IRQ3
Serial Port2 Address
Use this item to enable or disable the onboard parallel port, and to
assign a portaddress.
Disabled
3F8/IRQ4
2F8/IRQ3
3E8/IRQ4
2E8/IRQ3
Parallel Port Address
Use this item to enable or disable the onboard COM2 serial port, and to
assign a portaddress.
Disabled
378
278
3BC
Parallel Port Mode
Use this item to select the parallel port mode. You can select Normal
(StandardParallel Port), ECP (Extended Capabilities Port), EPP
(Enhanced Parallel Port), orBpp (Bi-Directional Parallel Port).
Normal
EPP
ECP
EPP+ECP
Parallel Port IRQ
Use this item to assign IRQ to the parallel port.
IRQ5
IRQ7
Содержание Veriton M6618G
