Acer Veriton 3600G Скачать руководство пользователя страница 94

Страница: 94 / 155

Veriton 3600(D/G)/5600(D/G)/7600(D/G)

Removing the Power Supply

See “Removing the Housing Cover” on page 76

See “Removing a Dummy Link Bar” on page 77

See “Removing a Link Bar” on page 77

Disconnect the FDD power connector from the FDD drive and the HDD power connector from the HDD..

Disconnect the CD-RW power connector from CD-RW drive and DVD-ROM power connector from DVD-
ROM drive.

Disconnect the main power connector and 12 Volt. power connector from the main board. Remove the
four screws that hold the power supply to the housing and detach the power supply from the housing.

Removing the Intrusion Alarm Cable Module

See “Removing the Housing Cover” on page 76

Disconnect the cable as shown here, remove the one screw here, and then detach the intrusion alarm
cable module from the housing.

Removing the LED Activity Indicators Module

See “Removing the Housing Cover” on page 76

Press the LED activity indicators module to release the latches in the direction as shown here, and then
detach the module from the housing.

Содержание Veriton 3600G




























































































































































Результаты поиска

Содержание Veriton 3600G

Отзывы:

Похожие инструкции для Veriton 3600G

Бренды по названию

Популярные бренды

Acer Veriton 3600G, Руководство по обслуживанию

Результаты поиска

Содержание Veriton 3600G

Отзывы:

Похожие инструкции для Veriton 3600G

Бренды по названию

Популярные бренды