manualshive.com logo in svg

Acer Veriton 3600G, Руководство по обслуживанию

Поделиться
Скачать
Acer Veriton 3600G Скачать руководство пользователя страница 85

76

Chapter 3

Disassembling the Veriton 5600D/ 5600G

Open the Housing Cover

This section tells you how to open the housing cover when you need to install additional components inside 
the system unit.

CAUTION: 

Before you proceed, make sure that you have turned off the system and all peripherals connected 

to it. 

Removing the Housing Cover

1.

Turn off the system power and unplug all cables.

2.

Place the system unit on a flat, steady surface.

3.

Turn the two thumbscrews counterclockwise to remove the cover.  Set the screws aside.  You will need 
them when replacing the housing cover.

4.

Hold the sides of the cover with both hands. Slide it back about an inch and then gently pull it outward to 
detach it

.

Removing the Front Panel

1.

See “Removing the Housing Cover” on page 76

2.

Release the latches as shown here and then detach the front bezel from the front panel gently in the way 
as shown here.

Содержание Veriton 3600G




























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды