Acer Veriton 3600G Скачать руководство пользователя страница 87

Страница: 87 / 155

Chapter 3

Removing the AGP VGA Card

See “Removing the Housing Cover” on page 76

Remove the screw on the bracket of the AGP card. Set the screw aside, you will need it when inserting
the AGP card.

Gently pull out the AGP card to remove it from the AGP slot

NOTE:

There is no AGP slot for Veriton 5600.

NOTE:

When you turn on the system, BIOS automatically detects and assigns resources to the PCI or AGP

devices.

Removing the Modem Card

See “Removing the Housing Cover” on page 76

Remove the one screw as shown below and then remove the modem card from the PCI slot

NOTE:

When you turn on the system, BIOS automatically detects and assigns resources to the PCI or AGP.

Removing the USB/ Audio Board Module

See “Removing the Housing Cover” on page 76

See “Removing the Modem Card” on page 78

Disconnect the USB cable and the memory stick cable from the main board

Remove the two screws as shown here and then detach the USB/ Audio board

Содержание Veriton 3600G




























































































































































Результаты поиска

Содержание Veriton 3600G

Отзывы:

Похожие инструкции для Veriton 3600G

Бренды по названию

Популярные бренды

Acer Veriton 3600G, Руководство по обслуживанию

Результаты поиска

Содержание Veriton 3600G

Отзывы:

Похожие инструкции для Veriton 3600G

Бренды по названию

Популярные бренды