background image

 

2

 

Safety instructions 

 
These  Safety  instructions  should  always  be  kept  with  the  step.  The 
operator must be made aware of these instructions before operating 
the Step. Read and follow these safety instructions carefully.

 

 
The step is intended to be an extra step to enter a vehicle. It should be used appropriately by 
passengers to enter or exit a minibus, taxi camper or other  vehicle, and the maximum load 
should not be exceeded. 

 

1.

 

Before operating the step the vehicle must be stationary and the hand brake 
or parking brake must be applied.  

2.

 

Before operating the step, ensure that there is nothing obstructing it. Look out 
for people moving outside the vehicle near the step.  

3.

 

It  is  recommended  that  the  step  is  only  operated  by  the  driver  or  other 
qualified operators. 

4.

 

The  driver  or  operator  must  have  a  clear  view  of  the  step  when  they  are 
operating it. 

5.

 

It is recommended that the middle of the platform is used when stepping onto 
the step. 

6.

 

NEVER drive away when the RED dashboard LED light is still on, this means 
that the step is not properly stowed. 

7.

 

The  step  platform  must  be  kept  clean  and  free  of  oil  and  other  greasy 
materials. 

8.

 

If  there  is  any  doubt  about  the  safety  of  a  passenger  when  using  the  step, 
ensure they are assisted. 

9.

 

If  you  have  any  questions  about  the  safe  operation  of  the  step,  contact  the 
person responsible directly. 

10.

 

Never use the step for any other use than described here. 

11.

 

Never overload the step. 

12.

 

The step should always be operated until it is fully in or out. 

13.

 

Repair and maintenance must be done by qualified and trained staff only. 

14.

 

If any parts need replacing, ensure only original Acdeos Parts are used.  

15.

 

If  the  anti  slip  profile  on  the  step  becomes  worn,  the step  platform  must  be 
replaced.  

16.

 

Always use the recommended cleaning materials. 

17.

 

Report any unsafe aspects of the step to the step supplier. 

 

Содержание AXS MD 600 M













Отзывы: