background image

 

- 2 - 

14.

Waste electrical products should not be disposed of with household waste.  Please 

recycle where facilities exist. Check with your local authority or retailer for recycling advice. 

15.  If  the  supply  cord  is  damaged,  it  must  be  replaced  by  the  manufacturer,  its  service  agent  or 

similarly qualified persons in order to avoid a hazard. 

16. Watch the moving door and keep people away until the door is completely opened or closed. 

17. Take care when operating the manual release since an open door may fall rapidly due to weak or 

broken springs, or being out of balance. 

18. Check the condition of the door frequently if has any damage or if is well balanced., especially 
the  cable,  spring,  components  connect  with  the  wall.  Don‟t  use  the  door  if  it  is  not  repaired  or 

adjusted, or there will be injury due to improper installation or bad balance. If the door components 
are under extreme pressure, don‟t repair it by yourself, if necessary, call for authorized service. 

19. Each month check that the drive reverses or the object can be freed when the door contacts a 50 

mm high object placed on the floor. 

20. The drive must not be used with a door incorporating a wicket door (unless the drive can not be 

operated with the wicket door not put in the safe position). 

If  applicable,  that  the  drive  is  not  to  be  used  with  doors  having  openings  exceeding  50  mm  in 

diameter or having edges or protruding parts a person could grip or stand on. 

21. 

Don‟t open/close the door when people are near the door. Keep children away from the moving 

door. Or it may cause serious personal injury and/or property loss. 

22. In orde

r to keep the GDO away from the rain, don‟t expose it out door. Don‟t put the GDO in the 

water, don‟t spray water to the GDO, keep the GDO away from any other device with water. 

23. In order to make sure the GDO can sense the obstacle under the door, the door must press the 

obstacle. So it may cause injury or damage to the obstacle, door or person. 

24. If the circuit is damaged, the professional person is required to do the repair. 

25. Make sure the garage door is fully open & stationary before passing through the door. Make sure 

the garage door is fully closed & stationary before leaving. 

 

The device is intended for the opening and closing of tilt-up and sectional garage doors in the private 

sector.   

For 600N, it is the best for the door less than 10m², 100kgs.   

For 800N, it is the best for the door less than 12m², 120kgs.   

For 1000N, it is the best for the door less than 14m², 140kgs.   

For 1200N, it is the best for the door less than 16m², 160kgs.   

For 1500N, it is the best for the door less than 18m², 180kgs. 

The device is not meant for commercial use but solely for the use in private garage doors that are 

appropriate for a single household. The device is installed indoor and max 2,5m away the door, and 

min 0,5m away the ceiling of garage. Check the Installation instruction for details. Any improper use 

of the drive could increase the risk of accidents.   

 

 

 

 

Содержание RAPTOR





















Отзывы: