Accutrol IAQ-Tek Скачать руководство пользователя страница 2

W

ARRANTY 

S

TATEMENT

 

 
 
 

Accutrol  LLC,  having  its  principal  place  of  business  at  21 Commerce Dr.  Danbury, CT  USA  ("Manufacturer")  warrants 
its IAQ-TEK Outdoor Airflow Transmitter product (the "Products") as follows: 

 

1.  Limited Warranty. 
Manufacturer warrants that the Products sold hereunder will be free from defects in material and workmanship for a 
period of thirty-six (36) months from the date of purchase.   If the Products do not conform  to this Limited Warranty 
during  the  warranty  period  (as  herein  above  specified),  Buyer  shall  notify  Manufacturer  in  writing  of  the  claimed 
defects and demonstrate to Manufacturer

s satisfaction that said defects are covered by this Limited Warranty.  If the 

defects  are  properly  reported  to  Manufacturer  within  the  warranty  period,  and  the  defects  are  of  such  type  and 
nature as to be covered by this warranty, Manufacturer shall, at its own expense, furnish, replacement Products or, at 
Manufacturer's  option,  replacement  parts  or  services  for  the  defective  Products.    Shipping  and  installation  of  the 
replacement Products or replacement parts shall be at Buyer's expense. 

 

2.  Other Limits. 
THE FOREGOING IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE 
IMPLIED  WARRANTIES  OF  MERCHANTABILITY  AND  FITNESS  FOR  A  PARTICULAR  PURPOSE.    Manufacturer  does  not 
warrant  against  damages  or  defects  arising  out  of  improper  or  abnormal  use  or  handling  of  the  Products;  against 
defects  or  damages  arising  from  improper  installation  (where  installation  is  by  persons  other  than  Manufacturer), 
against  defects  in  products  or  components  not  manufactured  by  Manufacturer,  or  against  damages  resulting  from 
such non-Manufacturer made products or components.  Manufacturer passes on to Buyer the warranty it received (if 
any) from  the maker  thereof  of such non-Manufacturer made products or  components.   This warranty also does not 
apply  to  Products  upon  which  repairs  have  been  affected  or  attempted  by  persons  other  than  Manufacturer  or 
pursuant to written authorization by Manufacturer.  This warranty also does not apply to any product provided by the 
Buyer and mounted by the Manufacturer to Products. 

 

3.  Exclusive Obligation. 
THIS WARRANTY IS EXCLUSIVE.    The  sole  and  exclusive  obligation  of  Manufacturer  shall  be  to repair  or replace  the 
defective  Products  in  the  manner  and  for  the  period  provided  above.    Manufacturer  shall  not  have  any  other 
obligation  with  respect  to  the  Products  or  any  part  thereof,  whether  based  on  contract,  tort,  strict  liability  or 
otherwise.   Under  no  circumstances,  whether  based  on  this  Limited  Warranty  or  otherwise,  shall  Manufacturer  be 
liable for incidental, special, or consequential damages. 

 

4.  Other Statements. 
Manufacturer's  employees  or  representatives'  ORAL  OR  OTHER  WRITTEN  STATEMENTS  DO  NOT  CONSTITUTE 
WARRANTIES, shall not be relied upon by Buyer, and are not a part of the contract for sale or this limited warranty. 

 

5.  Entire Obligation. 
This Limited Warranty states the entire obligation of Manufacturer with respect to the Products.   If any part of this 
Limited Warranty is determined to be void or illegal, the remainder shall remain in full force and effect. 

Содержание IAQ-Tek






















Отзывы: