manualshive.com logo in svg

Accu-Flo Meter Service Red Jacket AGUMP150S1, Установка, эксплуатация, обслуживание и запасные части

Поделиться
Скачать
Accu-Flo Meter Service Red Jacket AGUMP150S1 Скачать руководство пользователя страница 29

— 23 —

Figure 4.4 Packer with Functional Element 

7:   Install the UMP retaining bolts and lock washers.  Snug and then torque the bolts

using a cross pattern.  Torque to 7 ft-lb.(11 N•m).

Before replacing the extractable, make sure that the surfaces
of the packer o-ring and the discharge o-ring seals are clean.

8:

Replace the packer o-ring and the discharge o-ring seals. 

9:   Reinstall the extractable portion into the tank, using the steps previously described

under Installing the Pump in Chapter 2. 

10:  Refer to Chapter 3 to test system. 

R

EPLACING THE

F

UNCTIONAL

E

LEMENT

ALWAYS DISCONNECT and LOCK or TAG OUT the power
before starting to service the pump.  Then bleed off any 
residual pressure from the system.

Disable the Pump 

1:   Back out the electrical connector disconnect bolt.  (See fig. 4.4)

2:   Swing the electrical connector aside. 

3:   To relieve the pressure, back out Functional Element adjustment screw.

Replace the Functional Element

1:   Disconnect the siphon tubing (if siphon is installed).

2:   Remove the two 3/8” bolts.

3:   Carefully lift the functional element and remove it from the packer.  The old check

valve and spring will be resting inside the packer.

FUNCTIONAL

ELEMENT

3/8” BOLTS

ELECTRICAL

CONNECTOR

DISCONNECT

BOLT

ELECTRICAL CONNECTOR 

CAP

ADJUSTMENT

SCREW

Figure 4.5 Functional Element
cap and adjustment screw

NOTICE

DANGER

Содержание Red Jacket AGUMP150S1











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды