Accora Configura Скачать руководство пользователя страница 51

Страница: 51 / 60

Upholstery Care

Small dust and dirt particles can increase wear and tear of the fabric and dull the surface appearance,

therefore we recommend that you brush your furniture regularly using a soft brush or lightly vacuum.

Accora cannot be held responsible for any damage caused by cleaning.

The chair should not be exposed to direct sunlight for long periods of time as this will cause it to fade. If the

chair is positioned where it is exposed to sunlight for prolonged periods, ensure your curtains and blinds are

drawn for protection.

Ensure the chair is protected from sharp objects or buckles as these may cause the fabric to snag. If this

occurs do not pull the thread, carefully trim it with scissors.

Do not allow animals onto the chair as their claws may cause damage to the fabric. Animals also have a

degree of oil in their coats, and this may transfer to the upholstery causing premature wear.

The arms are designed for resting your arms only. Do not sit on them as this could cause structural damage

to the product.

Cleaning

1) To remove light stains use warm water and an ordinary detergent.

2) Scrape off solids, do not scrape against the grain of the fabric.

3) More difficult stains will benefit from a safe solvent such as Isopropyl Alcohol or Mineral Spirit.

4) Do not dry clean and do not immerse the fabric fully in water.

Regulations

The Configura

chair complies with the following:

BS EN 12520:2010 - Strength, durability and safety - Requirements for domestic seating

BS EN 1022:2005 - Domestic Furniture - Determination of Stability

Flame retardancy

Main chair fabric

The fabric on the main body of the chair conforms to BS 5852 Part 1 Cigarette & Match test when tested with

flexible urethane foam at nominal density of 22kg/cm and BS 5852 1990 CRIB ignition source 5 when tested

over non-combustion modified foam with a density of approximately 35kg/cm. Reference RB35H.

Vapour permeable fabric (on seat base and legrest)

Flammability: BS7175 ignition 0.1 and 5 over CMHR foam.

Standard foam

The standard foam used in the chair (Kovafoam CME-3025) has been tested at FIRA International Limited and

successfully satisfied the requirements from:

Schedule 1 part 1 of the Furniture and Furnishings (fire) (safety) regulations 1988, amended 1989 and 1993

(based on BS 5852; 1982 part 2). Report reference: TFFLF16293.

Visco foam

The Visco foam on the Configura

meets the requirement of the furniture and furnishings (fire) (safety) regulations

1988.

Cushionair cushion

This cushion meets BS EN ISO 12952 parts 1 and 2 flammability test.

Содержание Configura





























































Результаты поиска

Содержание Configura

Отзывы:

Бренды по названию

Популярные бренды

Accora Configura, Инструкция по эксплуатации

Результаты поиска

Содержание Configura

Отзывы:

Бренды по названию

Популярные бренды