manualshive.com logo in svg

Access ATB420 series, Руководство по обслуживанию

Поделиться
Скачать
Access ATB420 series Скачать руководство пользователя страница 31

Access keyboards ATB 420/421 Multi-Function Keyboard Product Specification and Service Guide 

 

___________________________________________________________________________ 

Rev 6 

 Access Keyboards 2001 & 2002 - All rights reserved               Page  31 of 37 

 

To re-assemble the matrix back into the keyboard base, hold the matrix at the back and locate the 
mouse switch PCB tangs and the chassis plate into the base moulding apertures at the front of the 
keyboard.  Tilt the keyboard towards you and carefully ease the TACT switches under the mouse 
keys and then gently lower the matrix into position. Replace the 3 screws and locate the matrix 
ribbon into its connector.  Check that the tactile feel of the mouse tact switches.  

7.2.4  Replacement of individual key switches

. 

The ATB420 uses replaceable switches and has a high quality PTH (Plated Through Hole) circuit 
board, which enables switches to be replaced by an operator who is trained in desoldering 
techniques.  The recommended procedure for replacing a switch is as follows. 

 

 

 

 

Step 1 
 
Desolder the four pins of the switch to be removed  

Step 2 
 
Ensure that all the solder is removed around 
the pins and that the pins are free to move. 

 

 

Step 3 
 
Push down on the centre plastic pin of the switch.  

Step 4 
 
Inspect the circuit board to check that the 

All manuals and user guides at all-guides.com

all-guides.com

Содержание ATB420 series






































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды