background image

Assembly Instructions / Turbochargers A131-R, A136-R

5 Storage of new turbochargers and spare parts / ​ 

© Copyright 2023 Turbo Systems Switzerland Ltd. All rights reserved.

HZTL455311P0044_EN

Rev. A

April 2023

5

Storage of new turbochargers and

spare parts

Storage of new turbochargers and spare parts up to 6 months

New turbochargers and spare parts can be stored in their closed packages and for 6 months from
the date of delivery without additional mothballing measures.

Only dry rooms in which the relative humidity is between 40…70 % and no condensation can form are
suitable for storage.

Storage of new turbochargers and spare parts for more than 6 months

As the contents of the package are adapted as required, turbochargers may also be delivered
without a VCI label.

For parts with a VCI label on the package, the following instructions must be observed.

Fig. 12: Volatile Corrosion Inhibitor (VCI)

 WARNING

Health protection when handling VCI

VCI products are not hazardous in terms of the Ordinance on Hazardous Sub-
stances. Nevertheless, the following points must be observed when handling VCI:

u

Observe the information in the material safety data sheet.

u

Ensure good room ventilation.

u

Do not eat, drink or store food at the workplace while working with VCI.

u

Clean your hands and face after working with VCI.

u

For further information refer to 

www.branopac.com

.

Wear safety gloves to protect against mechanical hazards.

Every 6 months, the following corrosion protection measures must be carried out:

u

Open the package.

u

Remove the VCI corrosion protection emitter from the package and replace it with a new, identical
VCI corrosion protection emitter. New VCI corrosion protection emitters can be obtained at

www.branopac.com

.

u

Dispose of the old VCI corrosion protection emitter in an environmentally compatible manner, pro-
fessionally and in accordance with local regulations.

u

Close the package. The more tightly the package is sealed, the longer the corrosion protection
will last.

Page 

15

 / 

17

Содержание Turbocharger A131-R





















Отзывы: