background image

Assembly Instructions / Turbochargers A131-R, A136-R

2 Safety / 2.3 Occupational safety

© Copyright 2023 Turbo Systems Switzerland Ltd. All rights reserved.

HZTL455311P0044_EN

Rev. A

April 2023

Mechanical hazards when working on the turbocharger

 WARNING

Mechanical hazard

Severe injuries to personnel or fatal accidents can be caused by mechanical influ-
ences as a consequence of hazardous and inadequate operational procedures.

u

Observe the general rules for occupational safety and prevention of accidents.

u

Ensure workplace safety.

u

Only perform operations that are described in this chapter.

u

Only perform operations for which you have previously received instruction or
training.

Hazards due to operating materials and supplies

Operating materials and supplies can include: Oils, greases, coolants, cleaning agents and solvents,
acids or similar substances.

 WARNING

Handling operating materials and supplies

Swallowing or inhaling vapours of operating materials and supplies or contact with
them may be harmful to health. Flammable and combustible operating materials
and supplies can catch fire or resulting vapours can lead to an explosion.

u

Do not breathe in these substances and avoid contact with the skin.

u

Ensure proper ventilation.

u

Observe the information in the material safety data sheet for the operating ma-
terials and supplies.

u

Comply with local legislation.

Wear safety goggles.

Wear safety gloves to protect against mechanical hazards.

Wear a respiratory mask to protect against gases.

Page 

8

 / 

17

Содержание Turbocharger A131-R





















Отзывы: