manualshive.com logo in svg

Accel Crestline Altra Series, Руководство по установке

Поделиться
Скачать
Accel Crestline Altra Series Скачать руководство пользователя страница 30

30

BASIC OPERATION

A. Make sure all rollers are in place.

B. Attach splash shield to the dampener.

C. Mount plate to cylinder. Wipe down all plates before running.

Pre-ink the Crestline

®

 Altra

TM

 Series dampener before running

the plates with an extremely light coverage of ink.

D. Adjust circulator flow to water pans.

NOTE: Accel recommends using the proper fountain solution
for the plate material being run on the press. A good acid/gum
etch should be used with metal plates.

A. In general, the Crestline

®

 Altra

TM

 Series Dampener should not

have to be adjusted from job to job. The form roller setting
should never be changed unless it has deviated from the factory
specification of 5/32" to the plate.

B. Adjustment of the amount of water fed to the plate is made by

altering the pan roller to metering roller pressure. Less pressure
equals more water.

C. In general, more water will only be required when going from a

metal plate to an electrostatic or silvermaster type plate.

START OF DAY

RUNNING

DURING THE DAY

Содержание Crestline Altra Series










































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды