AC Pro AWHD(30)ND3G/O, Руководство по установке

Страница: 37 / 44

35
Technical Information
Step Procedure
8. Remove electric box assy
1. Remove the grounding wire screw on the
electric box assy and then remove the
grounding wire.
2. Disconnect the wiring terminals of reactor,
compressor, high and low pressure
switch, compressor overload protector,
temperature sensor, outdoor fan motor
and 4-way valve. (See fig 2) Note: keep
pressing the circlip when disconnecting
the wiring terminal of reactor; keep
pressing the retainer when disconnecting
other wiring terminals.
3. Remove the wire inside the wiring groove.
9. Remove blade, motor, motor support,
reactor
1. Remove nuts fixing axial flow blade with
wrench, and then remove the axial flow
blade.
2. Remove 2 screws connecting motor
support and chassis, loosen damper block
and then remove the motor support.
3. Remove 4 screws fixing motor,and then
remove the motor
4. Remove 4 screws fixing reactor sub-assy
and motor support, and then remove the
reactor sub-assy.
10. Remove 4-way valve
Unsolder the spot weld between 4-way valve
and vapour liquid separator, compressor cut-
off valve sub-assy and condenser, and then
remove the 4-way valve.
Note: When unsoldering the spot weld, wrap
the 4-way valve with wet cloth completely
to avoid damage to valve due to high
temperature.
52
Installation and Maintenance
Service Manual
Steps Procedure
blade
motor support
motor
electric box assy
1.Remove the grounding wire screw on the electric
box assy and then remove the grounding wire.
2.Disconnect the wiring terminals of reactor,
compressor, high and low pressure switch,
compressor overload protector, temperature sensor,
outdoor fan motor and 4-way valve. (See fig 2)
Note: keep pressing the circlip when disconnecting
the wiring terminal of reactor; keep pressing the
retainer when disconnecting other wiring terminals.
3.Remove the wire inside the wiring groove.
8. Remove electric box assy
9. Remove blade, motor, motor support, reactor
1.Remove nuts fixing axial flow blade with wrench,
and then remove the axial flow blade.
2.Remove 2 screws connecting motor support and
chassis, loosen damper block and then remove the
motor support.
3.Remove 4 screws fixing motor,and then remove
the motor
4.Remove 4 screws fixing reactor sub-assy and
motor support, and then remove the reactor sub-
assy.
Unsolder the spot weld between 4-way valve and
vapour liquid separator, compressor cut-off valve
sub-assy and condenser, and then remove the 4-way
valve.
Note: When unsoldering the spot weld, wrap the
4-way valve with wet cloth completely to avoid
damage to valve due to high temperature.
10 Remove 4-way valve
4-way valve
52
Installation and Maintenance
Service Manual
Steps Procedure
blade
motor support
motor
electric box assy
1.Remove the grounding wire screw on the electric
box assy and then remove the grounding wire.
2.Disconnect the wiring terminals of reactor,
compressor, high and low pressure switch,
compressor overload protector, temperature sensor,
outdoor fan motor and 4-way valve. (See fig 2)
Note: keep pressing the circlip when disconnecting
the wiring terminal of reactor; keep pressing the
retainer when disconnecting other wiring terminals.
3.Remove the wire inside the wiring groove.
8. Remove electric box assy
9. Remove blade, motor, motor support, reactor
1.Remove nuts fixing axial flow blade with wrench,
and then remove the axial flow blade.
2.Remove 2 screws connecting motor support and
chassis, loosen damper block and then remove the
motor support.
3.Remove 4 screws fixing motor,and then remove
the motor
4.Remove 4 screws fixing reactor sub-assy and
motor support, and then remove the reactor sub-
assy.
Unsolder the spot weld between 4-way valve and
vapour liquid separator, compressor cut-off valve
sub-assy and condenser, and then remove the 4-way
valve.
Note: When unsoldering the spot weld, wrap the
4-way valve with wet cloth completely to avoid
damage to valve due to high temperature.
10 Remove 4-way valve
4-way valve
52
Installation and Maintenance
Service Manual
Steps Procedure
blade
motor support
motor
electric box assy
1.Remove the grounding wire screw on the electric
box assy and then remove the grounding wire.
2.Disconnect the wiring terminals of reactor,
compressor, high and low pressure switch,
compressor overload protector, temperature sensor,
outdoor fan motor and 4-way valve. (See fig 2)
Note: keep pressing the circlip when disconnecting
the wiring terminal of reactor; keep pressing the
retainer when disconnecting other wiring terminals.
3.Remove the wire inside the wiring groove.
8. Remove electric box assy
9. Remove blade, motor, motor support, reactor
1.Remove nuts fixing axial flow blade with wrench,
and then remove the axial flow blade.
2.Remove 2 screws connecting motor support and
chassis, loosen damper block and then remove the
motor support.
3.Remove 4 screws fixing motor,and then remove
the motor
4.Remove 4 screws fixing reactor sub-assy and
motor support, and then remove the reactor sub-
assy.
Unsolder the spot weld between 4-way valve and
vapour liquid separator, compressor cut-off valve
sub-assy and condenser, and then remove the 4-way
valve.
Note: When unsoldering the spot weld, wrap the
4-way valve with wet cloth completely to avoid
damage to valve due to high temperature.
10 Remove 4-way valve
4-way valve