background image

 

English 

Important Safety Instructions 

 

Appropriate use 

Use the device exclusively for the purpose for which it was built and designed! Any other use is 
considered as not intended! 

Damage caused by disregarding these safety instructions invalidates the warranty. We assume 
no liability for consequential damages! 

 

Unpacking 

While unpacking the device, handle it with extreme care. Packaging and packaging aids are recyclable 
and should always be sent for recycling. 

If the original packaging is damaged, first check the device. If the device is damaged, return it 
with the packaging and inform the delivery service. 

 

 

Please ensure that the packaging contains the DSK (Device Specific Key) card. 
This card shows the DSK of your ABUS Z-Wave device. Please keep them in a safe 
place. Every S2 (Security 2) certified Z-Wave controller requires the DSK to include 
the product in the Z-Wave network. 

 

Installation site Operating environment 

Do not place any heavy objects on the unit. The device is only designed for operation in rooms with 
appropriate temperature or humidity (e.g. bathrooms) or excessive dust. For an exact specification 
check the technical data of the individual devices. Ensure that there is always adequate ventilation, no 
direct heat sources are applied to the device, no direct sunlight or strong artificial light is applied to 
indoor equipment, the device is not in the immediate vicinity of magnetic fields (e.g. loudspeakers), no 
open fire sources (e.g. Burning candles) on or next to the unit, contact with splashing and dripping water 
on indoor units and aggressive liquids is avoided, the unit is not operated near water, in particular, the 
unit must never be submerged (do not place objects filled with liquids, e.g. vases or drinks on or next 
to the unit), no foreign objects may enter the unit, the unit is not exposed to strong temperature 
fluctuations, as otherwise air humidity may condense and lead to electrical short circuits, the unit is not 
exposed to excessive shocks and vibrations. 

 

Children 

Do not allow electrical devices to get into the hands of children! Never allow children to use electrical 
equipment unsupervised. Children are not always able to recognize possible dangers correctly. Small 
parts can be fatal if swallowed. Also keep the packaging film away from children. There is danger of 
suffocation! This device should not be handled by children. Springy parts can jump out if used 
improperly and cause injuries (e.g. eyes) to children. 

 

 

Содержание PLBW10000



















Отзывы: