manualshive.com logo in svg

ABSCO SHEDS CG56552N2, Руководство по сборке и инструкция

Поделиться
Скачать
ABSCO SHEDS CG56552N2 Скачать руководство пользователя страница 25

Absco Industries

Assembly Instruction Manual

ABSCO COMPACT GARAGE

MODEL: CG56552N2

5.64m W x 5.49m D x 2.64m H

Model: CG56552N2

16/10/19

25  

 

 

Fit Gutter And Downpipe

Join lengths of gutter to match the length of the garage by notching the rolled edge of one 

to allow the other to slide into it. Put silicone in the joint then use rivets to fasten the sections 
together. Repeat this procedure for the other side.

Mark the holes to be cut to accept the downpipe drop at the ends you select. Fix the drop 

Mark a line 110mm down from the top of the outer purlins at each end of the garage. Run a 

stringline between these marks. This line represents the bottom position of the gutter 
brackets, which are attached to each sheeting rib. You may wish to allow for a slight fall to 
the downpipe position (personal preference).

Fix gutter onto brackets equally at both ends, push top of bracket into outer roll of gutter 

and bend small support arm down to retain inner face.

Rivet brackets to gutter through the bottom of each bracket.

Fit downpipes to drops with silicone and rivets, then secure to a rib of the wall sheeting with 

screws from the inside of the garage.

Gutter

Downpipe drop

Gutter stop end

Cut hole for drop at 
back edge of gutter

Bend down the two arms 
on the bracket over the 
back edge of the gutter.

Содержание CG56552N2




































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды