ABSCO SHEDS CG56552N2 Скачать руководство пользователя | Manualshive

Страница: 1 / 35

background image

Absco Industries

Assembly Instruction Manual

ABSCO COMPACT GARAGE

MODEL: CG56552N2

5.64m W x 5.49m D x 2.64m H

Model: CG56552N2

16/10/19

1

AU: 1800 029 70

1

NZ: 0800 466 444

[email protected]

www.abscosheds.com.au

For construction in non-cyclonic areas

Wind rating: N2 as per AS4055-2012.
If you require a higher wind rating please contact
us: [email protected] or 1800 029 701

*The frame must be secured to a concrete slab
or footings, details of which are noted on the
attached engineering drawings. Brackets for
securing the frame to either a concrete slab or
footings are included in this kit. Anchors are not
included.

Local authority approval must be obtained prior
to construction. Once you have selected your
site, draw a site plan and lodge your application
together with a copy of the engineering plans
located at the back of these instructions.

Opening width: 4400mm
Opening height: 2210mm
Internal wall height: 2170mm

Download the Absco
Sheds Assembly App
for instructional videos

MANUFACTURED

IN AUSTRALIA

SNAPTiTE

Assembly

5.64 x 5.49 m x 2.64

1
2
3
...
»

Содержание CG56552N2




































Отзывы:

Нет отзывов

Похожие инструкции для CG56552N2

Бренд: Napier Страницы: 10

Бренд: Vango Страницы: 2

Бренд: Active Grow Страницы: 2

Бренд: Bestway Страницы: 16

Sportz SUV Tent Series

Бренд: Napier Страницы: 10

Бренд: HAMPTON BAY Страницы: 4

Бренд: Mammoth Страницы: 2

SUNDOME 9260F907

Бренд: Coleman Страницы: 2

grand illusion ii/ grand illusion iv

Бренд: Jack Wolfskin Страницы: 8

Pro SwiftRise Hub 3P Tent

Бренд: Magellan Outdoors Страницы: 8

20’x10’ Carport Canopy

Бренд: kdgarden Страницы: 8

Fast Peak Frame 20 x 20

Бренд: Infinity Страницы: 2

Бренд: Ev-ent Hire Страницы: 2

Copper Canyon 4 & 6 Tents

Бренд: Eureka! Tents Страницы: 2

Бренд: Clas Ohlson Страницы: 16

Бренд: Trigano Страницы: 16

Бренд: SereneLife Страницы: 2

Бренд: SereneLife Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды