ABL METERL Скачать руководство пользователя страница 4

Страница: 4 / 34

Additional technical information

Additional technical information

Additional technical information is required to install the controller/extender charging stations and the control unit

from ABL, as well as to set up a group installation. It is contained in separate documents.
In addition, the technical data for the METERS | METERL load management systems and the compatible products are

collated in product-specific data sheets. You can download these documents from the ABL website using the follow-

ing link:

https://www.ablmobility.de/en/service/downloads.php

NOTE

Displaying the additional information on a computer, tablet or smartphone

Additional technical information is made available in the Portable Document Format (PDF).

To display PDF files, you need the free Adobe Acrobat Reader or comparable software.

You can find further information about our product range, as well as about separately available accessory compo-

nents on our website at

www.ablmobility.de

. Please visit:

https://www.ablmobility.de

Intended use

METERS | METERL is an external load management system for a single controller charging station or a group in-

stallation controlled via an eMH2 or eMH3 controller wallbox, an eMC2 or eMC3 controller charging pole or via the

1V0001/1V0002 external control unit. METERS | METERL allows dynamically controlled, efficient distribution of the

available charging current to up to 16 charge points by measuring the energy flow via the three cable type current

transformers supplied and feeding the values back to the controller. METERS measures currents up to 300 A, METERL

up to 600 A, ensuring that electric vehicles can charge at the maximum available charging current.

Information in this document

This document describes how to install the three cable type current transformers and the energy meter as well as

how to subsequently configure them on the energy meter and via the ABL User Interface software. It is recommended

that all working steps described in this document are carried out by qualified specialist electrical contractors only.

User

Specialist electrical

contractor

Installation and Configuration Guide

(this document)
Additional technical information

Data sheets

Installation instructions for charging stations

(eMH2/eMH3/eMC2/eMC3) and control unit

(1V0001/1V0002)

Содержание METERL



































Результаты поиска

Содержание METERL

Отзывы:

Бренды по названию

Популярные бренды

ABL METERL, Руководство по установке и настройке

Результаты поиска

Содержание METERL

Отзывы:

Бренды по названию

Популярные бренды