110406_ABI-EV1012_QSG_ML.doc
English
Page
6
N.V.
abitana
S.A.
ENGLISH
8.
Turn on the power
9.
On the side of the Amplifier, a blue power adjustment screw
is available. Set it to the maximum position by gently rotating
the screw clockwise until it blocks.
10. Remove all termination plugs and patch cords of the
amplifier ABI-EV1012S00.
11. Insert the level tester ABI-TT1003S12 into port 1.
12. Please follow the instructions of the ABI-TT1003S12 to
adjust the power of the amplifier correctly.
13. Remove the power level tester and eventually reinsert the
previously removed termination plugs and patch cords.
14. Close the ‘Comm Center Cabinet’.
15. Locate the Outlet near your TV-set you want to connect
16. Take a TV/Video Balun (ABI-AC100XS00
*
), and set the level
to maximum by means of the power level adjustment screw
located on the balun (Turn the screw gently clockwise until it
blocks). Then insert the Balun into the free Outlet.
17. Insert one end of a coax patch cord (ABI-PC1006Sxx) into
the Balun (ABI-AC100XS00*)
18. Insert the other end of the Coax patch cord into the TV–set
or VCR
19. In the ‘Comm Center Cabinet’, locate the Comm Center
Connector that corresponds to the outlet where you just
inserted the Patch cord and insert one end of a ‘Comm
Center’ Patch cord’ of a suitable length into this connector.
20. Insert the other end of the Patch cord in one of the
numbered ports (P1–P4) on the front of the Amplifier.
21. Check the signal quality on the TV set; and adjust the level
by means of the level adjustment screw on the Balun if
necessary. Normally this is only required for short links
between the Comm center Cabinet and the outlet.
*ABI-AC1001S00, ABI-AC1002S00 or ABI-AC1007S00
IMPORTANT REMARK:
Insert a Termination Plug (ABI-AP1003S00) in every unused
port of the amplifier.
If all four ports are connected to outlets, but not all outlets
have a device (TV/VCR/…) connected to it, it is strongly
recommended to insert a Termination Plug (ABI-AP1003S00)
into the latter (unused) outlets.
It is possible to use the ABI-AC100XS00
*
Balun as a
Termination plug, by adjusting the Power Level Screw to its
minimum (Turn the Adjustment screw gently counter-
clockwise until it blocks), and insert the ABI-AC1001S00 into
the unused ports or outlets.
For IR functionality, the ABI-AC1007S00 Balun is required
Additional, and more detailed information concerning this product can
be found on the website: www.abitana.com .
Use the following table to write down information about the amplifier
and the connections.
Amplifier Serial #
.
Connection to
Coax
P1
P2
P3
P4
Antenna
Cable TV
[ ]
[ ]
[ ]
[ ]
Figure 1: Installation on DIN-rail
Recommendation regarding overvoltage protection
It is recommended to add an overvoltage protection to the incoming
signals. This protects the system against overvoltages caused by
power surges, lightning, etc.
A different type of protector is required for every type of signal
(Antenna/Cable TV (5) , Telephone (6) , Mains Power (7))
EV1002
ET100X
Power
Supply
DIN-Rail
Frame
PE1002
1
2
3
4
CATV
Antenna
PSTN /ISDN
Power
220V/240V
OVP
RF
OVP
TEL
OVP
POW
5
6
7
DC1015
