Abit IT5E Series Скачать руководство пользователя страница 61

Страница: 61 / 98

Introduction of BIOS

3-27

Onboard PS/2 Mouse:

This is to Enable or Disable the PS/2 Mouse. When in Enable, IRQ
12 is used.

On Board FDD Controller:

This is to Enable or Disable the Onboard FDD Controller.

On board Serial Port 1:

This is used to specify the I/O address and IRQ of Serial Port 1. Five
options are available: Disable, 3F8h/IRQ4, 2F8h/IRQ3, 3E8h/IRQ4
or 2E8h/IRQ3.

On board Serial Port 2:

This is used to specify the I/O address and IRQ of Serial Port 2. Five
options are available: Disable, 3F8h/IRQ4, 2F8h/IRQ3, 3E8h/IRQ4
or 2E8h/IRQ3.

Attention:

Do not select the same I/O address and IRQ for the two
serial ports, otherwise the serial ports will not be able to
operate normally.

Onboard IR Function:

Onboard serial port 2 can support IR (Infrared) function. Three
options are available:

Disable: No support for IR function.

IrDA (HPSIR) mode.

ASK IR (Amplitude Shift Keyed IR) mode.

IR Duplex Mode:

Set the IR mode as Half or Full. Default is Half.

IR Tr/Re Polarity:

Set IR transmission/reception polarity as High or Low.

On board parallel Port:

Set the I/O address and IRQ of the onboard parallel port. Four
options are available: Disable, 3BCh/IRQ7, 278h/IRQ5 and
378h/IRQ7. Default is 378h/IRQ7.

Содержание IT5E Series



































































































Результаты поиска

Содержание IT5E Series

Отзывы:

Abit IT5E Series, Руководство пользователя, Страница: 61 / 98

Результаты поиска

Содержание IT5E Series

Отзывы: