Abicor Binzel ABICLEANER 800 AC, Оригинальная инструкция по эксплуатации

Страница: 11 / 84

ABICLEANER 3 Product description
EN - 11
2.1 Designated use
► The device described in these instructions may be used only for the
purpose and in the manner described in these instructions. In doing so,
observe the operating, maintenance and servicing conditions.
► Any other use is considered improper.
► Unauthorised modifications or changes to enhance the performance are
not permitted.
2.2 Electro-technical safety instructions
► Check electric tools for damage and for their proper functioning in
accordance with their designated use.
► Do not expose electric tools to rain and avoid a moist or wet
environment.
► Protect yourself from electric shock by using insulating mats and wearing
dry clothing.
► Do not use the electric tools in areas subject to fire or explosion hazards.
2.3 Product-specific safety instructions
2.4 Safety instructions for cleaning and polishing
► Electromagnetic fields can impact cardiac pacemakers. People with
pacemakers may be work with this device and may not stand in the
immediate vicinity of the device.
► Carbon-fibre brush or electrodes and workpiece can become very hot.
This poses a risk of burns. Wear protective gloves.
► Any metal vapours, especially lead, cadmium, copper and beryllium are
harmful! Ensure sufficient ventilation or extraction. Do not exceed the
current threshold limit values (AGW).
► Do not place the cleaning tool on the workpiece. Otherwise, electric
current may flow.
2.5 Safety information on chemical substances
► Observe the safety data sheet for the electrolyte.
► Electrolyte splashes can cause burns to the eyes and skin. Always wear
the prescribed, acid-resistant protective clothing in accordance with the
relevant, local regulations.
► If electrolyte gets into the eyes, rinse immediately with plenty of water
and consult an ophthalmologist right away.
► Electrolyte splashes can cause burns on stone floors or other materials.
Wipe up electrolyte splashes immediately with plenty of water.
2.6 Safety instructions for use
► Do not exceed the maximum load data specified in the documentation.
Overloads lead to destruction.
► Do not make any constructive changes to the product.
► Do not use the device outdoors, in wet conditions, and in environments
where fire and explosion hazards may occur. Protect the device from
the effects of acids and alkalis. Do not expose the device to ionizing or
non-ionizing radiation, vibration, shock, or continuous shock.
2.7 Safety instructions regarding protective clothing
► Do not wear loose fitting clothing or jewelry.
► Use a hair net for long hair. ► Wear acid-proof safety goggles, protective gloves, and an apron.
2.8 Emergency information
In the event of an emergency, immediately disconnect the following supplies: ► Electrical power supply
3 Product description
Cleaning with carbon fibre brush removes contamination caused by welding
from the surface and renews the passive layer of the stainless steel. Polishing
with a carbon fibre brush removes material in the

range in addition to
cleaning, creating a polished surface. The device works with low direct
voltage (AC/DC), which poses no danger to people.
WARNING
Hazards caused by improper use
If improperly used, the device can present risks to persons, animals and material property.
► Use the device according to its designated use only.
► Do not convert and modify the device to enhance its performance without authorization.
► Ensure that only qualified personnel perform work on the device or system.
► Do not short circuit the carbon-fibre brush and the ground clamp. This can lead to a risk of burns.
► Do not touch uninsulated components of the grip handle and the ground clamp at the same time. This can lead to a risk of electric shock (harmless because
low-voltage).
CAUTION
Risk of injury and device damage when handled by unauthorized persons
Improper repair work and modifications to the product may lead to serious injuries and damage to the device. The product warranty will be rendered invalid if
work is carried out on the product by unauthorized persons.
► Ensure that only qualified personnel perform work on the device or system.