ABERLINK Axiom Too Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 21

background image

ABERLINK LTD

|

VATCH LANE

|

EASTCOMBE

|

GLOUCESTERSHIRE

|

GL6 7DY

|

UK

Tel : +44 (0)1453 884461

|

Fax : +44 (0)1453 882348

|

Email : [email protected]

|

Web : www.aberlink.com

Registered in England No. 7642245

|

VAT Registration No. GB 108 3075 37

HS machine setup

The drive unit is stored up inside the right leg.

Locate the drive assembly and
remove the plate shown.  The
two rubber mounts will take the
motor assembly. Fasten to the
bottom of the right leg as shown.

This picture also shows the
airbearing holding block, which is
also held in place with the same
screws.  Once in place locate
and connect the 4mm air pipe.
This feeds the pre-load bearing.

Fit the motor assembly in the
orientation shown by 2 screws,
which will screw into the
threaded rubber mounts. Align
the motor to be horizontal.

«
...
12
13
14
15
16
...
»

Содержание Axiom Too






















Отзывы:

Нет отзывов

Похожие инструкции для Axiom Too

Бренд: B meters Страницы: 18

Бренд: B meters Страницы: 14

Бренд: Callaway Страницы: 11

Бренд: Keithley Страницы: 201

Бренд: Valhalla Scientific Страницы: 43

Бренд: Hammond Страницы: 78

VOLUTANK Petro 3003

Бренд: Bartec Страницы: 10

Бренд: Yamaha Страницы: 8

Бренд: ETI Страницы: 2

XL4 SECOND STAGE

Бренд: Apeks Страницы: 21

Бренд: Omega Страницы: 59

Бренд: GasQuip Страницы: 8

Бренд: Hanna Instruments Страницы: 32

Бренд: Laguna Tools Страницы: 28

Бренд: Keison Страницы: 56

Бренд: VOLTCRAFT Страницы: 4

Бренд: novomatics Страницы: 39

NEO MP18X Series

Бренд: MA Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды