ABBINA IND 600 IX, Инструкция по эксплуатации

Страница: 6 / 24

GB
6 7
operate the front right cooking-zone select- key and
the MINUS-key simultaneously. “L” (LOCKED) in the
display extinguishes and all cooking zonesshow ”0”
with a blinking dot. Should a cooking zone be “hot”, “H”
is displayedinstead of the static ”0”. After switching OFF
the control, the child safety feature is active again.
Cancelling the key lock:
Afterswitching-ON the control the child safety feature can
be deactivated. Hereit is necessary to simultaneously
operate the front right cooking-zone-select key and the
MINUS-key and then operate the MINUS-key alone. If all
steps have been carried out in the right order within 10
secondsthe key lock gets cancelled and the control is
OFF. Otherwise the input will be considered incomplete,
the control remains locked and switches-OFF after 20
seconds. After a renewed switching-ON by means of
the ON/OFF key all displays show “0”, the display dot
sare blinking and the control is ready for cooking. If a
cooking zone is “hot”, “H” will be displayed instead of
the static “0”.
1.9 COMBIMODELS: partial switch-off of multiple circuits
Depending on the design it is possible to operate dual-
or triple-circuit radiant heating element swith the LITE-
Touch Control. When a multi-circuit heating elementis
put in to operation, all heating circuits are switched ON
at the same time.If only the inner heating circuits should
be used, the outer heating circuit can be switched-OFF
by means of the multi-circuit key or in individuaI steps.
By operating the multi-circuit key the respectiveouter
circuit of the assigned active cooking zone (setting1t
“0”) canbe cut off any time. An activated outer circuit
will be indicated by an additional LED. A renewed
operation of the multi-circuit key will add the outer circuit
(s) at anytime,the assigned LED”s glow again (toggle-
function) If a cookingzone other than the one with
multi-circuit function will be selected, the multicircuit
status will be changed and all cooking zones will be
deselected (the decimaI point extinguishes).
Behaviour of dual-circuit cutOFF:
If the heating element to be controlled is a triple-circuit
heating element, the course of action is as follows:
- The first activation of the multi-circuit key cuts-off the
outer heating circuit and the top LED extinguishes.
- A second activation of the multi-circuit-key cuts-
off the middle heating circuit (also the bottom LED
extinguishes.)
- A third activation adds the middle heating circuit
again. A for the ractivation adds the third heating
circuit as well and the assigned LEDs glow again.
1.10 Audiblesignal (buzzer)
While the control is in operation the following activities
will be signaled by means of a buzzer:
cooling down will be calculated dependenton on
- the selected setting (“0” to “9”)
- the ON/OFF time of the relays
After switching-OFF the cooking zone the respective
display shows “H” until the assigned cooking zone
temperature is mathematically in a uncritical level. (<
60°C).
1.7 Protection against unintended switcbing-ON
- If theelectronic control realizes a continuous operation
of keys forapprox. 10 seconds, it switches OFF
automatically. The control sends outanaudible failure
signal for 10 seconds, sothattheusercan remove the
object which has been mistakingly placed onto the
operation surface. The displays show the failure code
“ER03”.
- If the failure carries on for more than 10 seconds,
onlythe code ”ERO3” will be displayed as long as the
failure will be recognized by the electronic control. If
the cooking zoneisinthe”hot”status, “H” willappear on
thedisplay in alteration withthefailure notice.
- If no cooking zone will be activated within 20 seconds
after switching-ON by means of the Power-key, the
control switches back from the ON-condition in to the
stand-by-mode. (also see paragraph 1.2).
- When the control is switched ON the ON/OFF-key has
priority over all other keys, so that the control can be
switched-OFF anytime, even in case of multiple or
continous operation of keys.
- In the stand-by mode a continous operation will not be
signalized. How ever, before the electronic control can
be switched-ON again,it has to recognize that all keys
are not operated.
1.8 Key lock (cbild safety feature)
Child safety feature:
Key lock:
After switching-ON the control the child safety feature can be
activated. To achieve this it is necessary to simultaneously
operate the front right cookingzone- select-key and the
MINUS-keyand then press the front right cooking-zone-
select key again.There will be an “L”, meaning LOCKED
(child safety feature against unintended switching-ON).
If a cooking zone is in the “hot” condition,”L” and “H” will
be displayed in alternation. This course of operationhas to
take pIace with in a period of 10 seconds, no other key than
described above may be operated. Otherwise the input will
be interrupted because of incompleteness, the cooktop will
not be locked then. The electronic control remains in a locked
condition until it gets unlocked, even if the control has been
switched-OFF and-ON in the mean time.Also a reset of the
control (after a voltage drop) does not cancel the key lock.
Unlocking for cooking purposes:
To unlock and operate the controlit is requiredto