ABB Zenith ZTS T Series Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 44

background image

22

Ze nit h Z T S ( D) 3 0 -1 2 0 0A AT S , Q U I CK STA RT U S E R M A N UA L

—

Troubleshooting

Warning

Any troubleshooting should be conducted by trained and authorized personnel only. Appropriate personal
protectiveequipment (PPE) shall be used when troubleshooting the ATS panel.
Hazardous voltage may be present. Disconnect all power sources before performing work inside the ATS panel.
Failure to do so may result in serious injury or death.

—

Alarms

LCD

Touch

Message

Fault

Action

Locked, Alarm LED on

Lock input activated

Unlock

Switch not in AUTO
mode, Alarm LED on

Slide switch is in handle or lock

position

Turn slide switch into the AUTO position

Phases crossed

Phase rotation of sources 1 and 2 are

different

Connect the phases of both sources in

the same order

S1 undervoltage

Voltage of source 1 is under the

threshold level set in parameter “Drop-

out voltage, lower threshold“

Check the correlation between power

source and device configuration

S1 overvoltage

Voltage of source 1 is over the

threshold level set in parameter “Drop-

out voltage, upper threshold“

Check the correlation between power

source and device configuration

S1 phase missing

One or two phases of source 1 are

missing

Check the power source and

connections

S1 unbalance

Phases of source 1 are not symmetric

Check the power source

S1 phase rotation

Phase rotation of source 1 is different

from the value of parameter “Phase

sequence“

Connect the phases according to the

configuration

S1 invalid frequency

Frequency of source 1 is out of range

set in parameters “Drop-out frequency,

upper threshold“ and “Drop-out

frequency, lower threshold“

Check the correlation between power

source and device configuration

S2 undervoltage

Voltage of source 2 is under the

threshold level set in parameter “Drop-

out voltage, lower threshold“

Check the correlation between power

source and device configuration

S2 overvoltage

Voltage of source 2 is over the

threshold level set in parameter “Drop-

out voltage, upper threshold“

Check the correlation between power

source and device configuration

S2 phase missing

One or two phases of source 2 are

missing

Check the power source and

connections

Table 5 Alarms-list in level 3 and 4, LCD and touch control interfaces

«
...
20
21
22
23
24
...
»

Содержание Zenith ZTS T Series













































Отзывы:

Нет отзывов

Похожие инструкции для Zenith ZTS T Series

Бренд: N-Tron Страницы: 20

Бренд: D-Link Страницы: 267

Бренд: H3C Страницы: 1089

RackSwitch G8264

Бренд: IBM Страницы: 20

Flex System FC3171

Бренд: IBM Страницы: 64

Бренд: Camozzi Страницы: 2

M800 Elite Series

Бренд: 4B Страницы: 12

Бренд: Videplus Страницы: 13

Бренд: TESmart Страницы: 12

Бренд: Guntermann & Drunck Страницы: 8

Бренд: DeLOCK Страницы: 26

Бренд: Cable Electronics Страницы: 12

Signal Distribution Box SDB45

Бренд: Audiovox Страницы: 12

Бренд: AMBIENTECH Страницы: 4

Бренд: IOGear Страницы: 10

Бренд: Xantech Страницы: 5

Бренд: TRENDnet Страницы: 6

Бренд: Gembird Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды