ABB Zenith MX250 Скачать руководство пользователя

Страница: 6 / 36

ABB Zenith

ZTSCT / ZBTSCT Operation & Maintenance Manual

Installation

(cont’d)

NOTE

When the voltage and frequency

reach preset values, the Source 2

Available

LED

will illuminate.

Verify the phase to phase voltages at Source 2

line terminals.

Verify that the phase rotation of

Source 2 is the same as the phase

rotation of Source 1.

Shut down the generator’s engine.

(Place in Automatic Mode.)

NOTE

Source 2 Available LED will turn off.

NOTE

The engine generator will continue

to run for the duration of Source 2

Stop Delay Timer.

10. Place the disconnect switch to

ENABLE

11. Complete the visual inspection of the

transfer switch.

12. Close the enclosure.

13. Lock the enclosure.

Figure 5 – LCD and keypad

After all options and accessories are checked and verified,

follow these steps to set up the ATS. Refer to Entelli-Switch

250 display

Figure 5

. The annunciation LEDs illuminate

to indicate (1) source availability, (2) ATS position, and

(3) Entelli-Switch 250 control function (timing).

Unlock the enclosure.

Open the enclosure.

Place the Disconnect Switch in the Inhibit.

NOTE

This step is only performed if the

“DS” Option was purchased.

Close the external (up-stream) Source 1

circuit breaker.

NOTES

: Source 1 Available and Source 1

Position

LED

’s will illuminate.

If Source 1 Available

LED

does not

illuminate, verify that Source 1 Voltage

is above the preset restore value.

The Gen-Set will start and run while

Source 2 stop Delay Timer is timing.

Close the External (up-stream) Source 2 line

circuit breaker.

Start the engine generator in

MANUAL

mode.

When performing a hi-pot or

dielectric test on the power section,

DISCONNECT

the control panel plugs from

the microprocessor to avoid potential damage.

S 1 O K

2 1 : 5 6

M O N 2 3 A P R 2 0 0 8

M O R E

T E S T

WARNING

Figure 4

Certain accessories, per specific

schematics, can inhibit automatic transfer.

Engine Gen-Set could start when

engine control wires are attached.

Initial Energization

(cont’d)

CAUTION

SERIAL NUMBER:

RATING

VOLTS -
AMPS -

SYSTEM VOLTS:

MODEL NUMBER:

HZ -

PHASE -

ABB Zenith

Содержание Zenith MX250





































Результаты поиска

Содержание Zenith MX250

Отзывы:

Похожие инструкции для Zenith MX250

Бренды по названию

Популярные бренды

ABB Zenith MX250, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Zenith MX250

Отзывы:

Похожие инструкции для Zenith MX250

Бренды по названию

Популярные бренды