background image

12

ABB Zenith

ZTSCT / ZBTSCT Operation & Maintenance Manual

Accessory Definitions 

(cont’d)

R50

In Phase Monitor this feature restricts Live to Live Source

Transfers to occur unless both Sources are within 7 electrical

degrees or less of each other. (live Source to live Source

transfers usually occur during transfer back to Source 1

or during Testing). R50 does not change the operation of

the Automatic Transfer Switch in a power failure mode.

After all timer functions have elapsed, the CHECKING

FOR SOURCE SYNCHRONISM will be displayed as well

as the direction of transfer (S1-S2 for example denotes

transfer from Source 1 to Source2). When synchronism is

accomplished, transfer will take place.

Notes: - If S2 Frequency is less than S1 Frequency, 

display will show a series of (- - - - -…..) symbols.

- If S2 Frequency is greater than S1 Frequency, 

display will show a series of (+++++…..) symbols.

- Each (-) or (+) symbol represents 10 electrical

degrees out of phase. A maximum of 18 symbols
(180 electrical degrees) can be monitored.

- The number of (-) or (+) symbols decrease 

as the two sources approach synchronism 
and increase as the two sources drift out 
of synchronism.

- If S1 and S2 Frequencies are identical, the 

display will show a series of alternating 

- - - -

symbols (++++…) which also indicate the
approximate out of phase degrees

In the event that the Sources do not come within 7 electrical

degrees of each other within 60 seconds, the unit will display

the message: SYNCH CHECKING and will allow the user

to BYPASS. If the BYPASS button is pressed, the unit will

display the message: WARNING MAY CAUSE DAMAGE

TO THE LOAD. Pressing XFR will actually bypass the

R50. Since R50 is a passive device, the length of time it takes

to reach Synchronism is de-pendent on the frequency

difference between the two Sources. Source 1 is usually

a Utility and the frequency is not within the control of

the consumer. Source 2 needs to be adjusted to create an

adequate difference  in order for the transfer to happen a

timely fashion.
Note: For optimum performance, Source 2 Generator

should be adjusted a Maximum of 2 Hertz above 
or below the Utility frequency, minimum of 0.1 
Hertz. (58 to 59.9) or (60.1 to 62) Hertz.
Adjustment of Generator to 60Hertz could 
cause lengthy transfer delay

.

R50 Feature can be turned ON or OFF via CFG Menu

(see page 17). Factory Default if OFF.

S5P

Auto / Semi Manual selector

In “Auto” position, retransfer to Source 1 is automatic

after the T timer has timed out. The T time delay is

bypassed if Source 2 fails.

In “Manual”, retransfer to Source 1 is upon depression

of BYPASS DELAY button YEN or if Source 2 fails.

S12P

Auto / Manual Selector

In “Auto” position, the Automatic Transfer Switch functions

automatically as specified with the Switch drawings. In

“Manual” the Automatic Transfer Switch will transfer to

either direction upon depression of Source 1 or Source 2

transfer buttons. Should Source 1 fail, the Generator

(Source 2), will automatically start. Once transferred in

Manual, the Switch maintains position selected even if

selected power fails.

S13P

Transfer Commit. Configured via CFG menu. (see page 17)

When this Feature is set to OFF: The transfer Switch is not

committed to transfer unless the outage duration is longer

than the timers that precede the transfer to Source 2

position. This assumes that the outage will be an isolated

event. When this Feature is set to ON: The transfer Switch

is committed to transfer to Source 2 position once the

W timer has begun timing, even if Source 1 power returns

before the transfer to Source 2. This is to ensure that the

transfer takes place, because one outage may be followed

by another.

S14

Test / Auto / Source 1 Selector, Door mount

SW1

Auto/Off/Start   Engine control selector, Door mount

(Keyed or non-keyed operation available)

SW2

Auto / Off  Engine control selector, Door mount

(Keyed or non-keyed operation available)

SW3

Source Priority Selector Switch, Door mount

Allows selection of Source 1 or Source 2 to be the Prime

Source. Transfer Switch will transfer to selected Prime

Source if that Source is available. (Keyed or non-keyed

operation available)

T

Time Delay (S1) Source 1 Stable Timer. To delay transfer

to Source 1 (immediate retransfer on Source 2 failure).

Adjustable 0-60 minutes in 1 second increments. Standard

setting is 30 minutes. Adjust via SET menu (see page 18)

T3/W3

Elevator Pre-Signal Auxiliary Contacts: Open 0-60 seconds

prior to transfer to either direction, re-closes after transfer.

U

(S2) Source 2 Stop Delay Timer. Allows Engine to run

unloaded after switch retransfer to Source 1. Adjustable

0-60 minutes in 1 second increments. Standard setting is

5 minutes. Adjust via SET menu (see page 18)

Содержание Zenith MX250





































Отзывы: