ABB Zenith MX250 страница 13 Скачать руководство пользователя

Страница: 13 / 36

ABB Zenith

ZTSCT / ZBTSCT Operation & Maintenance Manual

Accessory Definitions

(cont’d)

Single Phase Amp Meter

Three Phase Amp Meter

M80

3000 Digital Power Monitor

M82

5200 Digital Power Meter

M83A

EPM 5300 Digital Power Meter with Modbus Port

M83B

EPM 5350 Digital Power Meter with Ethernet Port

M84

7430 Digital Power Meter , Wye or Delta

M85A

EPM 9450 Digital Power Meter, Ethernet

M85B

EPM 9450 Digital Power Meter with Internal 56K Mod.

M86A

EPM 9650 Digital Power Meter, Wye or Delta,

RS232 or RS485

M86B

EPM 9650 Digital Power Meter, Wye or Delta,

RS232 or RS485

Running Time Meter, Door mount

Operation Counter, Door Mount

Time Delay Source 2 Start. Adjustable 0-10 seconds.

Standard setting is 3 seconds. Adjust via SET menu

(see page 18)

Time Delay S2 Start. Adjustable 1/6 to 300 seconds.

Remote Peak Shave or Area Protection Circuit. Energize Q2

to simulate Source 1 Line failure causing the Generator to

start and transfer the load to Source 2. Should Emergency

fail during this operation, Transfer Switch will retransfer

back to Source 1.

Remote inhibit transfer to Source 2 circuit. Energize Q3

input to allow transfer to Source 2. To enable Q3 option,

engage Q3 jumper.

Inhibit transfer to Source 1 circuit. Energize Q7 input

to prevent transfer to Source 1.

R1-1/R1-3

Source 1 Over Voltage sensing for single and three

phase systems.

Source 1 Over Voltage “Fail”

Factory Default: 110%

This adjustment determines the maximum acceptable

over voltage. Adjust via the SET menu. Range is 105%

to 110% in 1% increments (see page 18). Once exceeded,

the P timer begins timing to signal the Generator to start.
Source 1 Over Voltage “Restore”

Factory Default: 105%

This adjustment determines the minimum acceptable

over Voltage threshold at which the Transfer Switch is

allowed to automatically transfer to Source 1. Adjust via

SET menu. Range is 103% to 108% in 1% increments.

“Restore” must be a minimum of 2% below “Fail” setting

(see page 18).

R15/R15D

Load Shed

Should Source 2 become overloaded, a signal can be

given to switch to the dead or Mid position.

R16

Phase Rotation Sensing

Can be turned on or off via CFG menu (see page 17).

Factory Default is on.

This feature prevents Line Source to Line Source transfers

from occurring between dissimilar phase sequences. This

condition is primarily caused by an installation error.

Connections from Source 1 and Source 2 need be verified,

compared, and corrected to remedy the inconsistent phase

rotation between the sources. WARNING: Turning off

this feature can cause severe damage to loads.

R26

Interruptable Power Rate Provisions. Allow transfer out

of Source 1 position to Source 2 or dead Source 2. Alarm

and Pre-Signal circuit included.

Содержание Zenith MX250





































Результаты поиска

Содержание Zenith MX250

Отзывы:

Похожие инструкции для Zenith MX250

Бренды по названию

Популярные бренды

ABB Zenith MX250, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Zenith MX250

Отзывы:

Похожие инструкции для Zenith MX250

Бренды по названию

Популярные бренды