ABB VSN730 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 28

background image

VSN730 System Monitor Product Manual

-

6 -

The System Monitor consists of a NEMA 4/4X rated steel enclosure containing a data

logger/gateway, AC/DC power supply, serial data line surge protection, and DC protection fuse.

The data logger connects to the Local Area Network (LAN) with an Ethernet RJ45 connection.

Typically it connects to a Digital Subscriber Line (DSL) or Cable router/gateway for internet access,

though any internet connection will work.
The System Monitor is available in two versions. The VSN730-03 has the capability to monitor up

to 10 ABB or Power-One legacy string inverters and one ABB (VSN800 Weather Station) or

Power-One legacy weather station. Inverters can be single-phase or three-phase string inverters.

The VSN730-05 has no software limitations on the number of devices it can monitor, but it is

recommended that no more than 20 devices be connected to each port.

Components

The picture below shows the interior of the System Monitor enclosure.

VAC Power

Landing Block

Data logger

Aurora Protocol

Landing Block/Surge Protector

Modbus RTU Protocol

Landing Block/Surge

Protector

Taps for 24VDC

Power with protection

fuse, and DC COM

Ethernet (Eth0) Port

for Internet

Connection

Ethernet (Eth1) Port

for Local Setup

Protective Earth

Ground Landing

Terminal

«
...
4
5
6
7
8
...
»

Содержание VSN730





























Отзывы:

Нет отзывов

Похожие инструкции для VSN730

System SourceMeter 2601B

Бренд: Keithley Страницы: 13

Бренд: Keller-druck Страницы: 8

Бренд: Landis+Gyr Страницы: 26

Бренд: Landis+Gyr Страницы: 3

Бренд: Parkside Страницы: 94

Бренд: SAGEMCOM Страницы: 33

Prestige Series

Бренд: Ibanez Страницы: 54

Clavinova CVP-805

Бренд: Yamaha Страницы: 112

Clavinova CLP-270

Бренд: Yamaha Страницы: 44

Бренд: Yamaha Страницы: 3

Veeder-Root 7990 Series

Бренд: Danaher Страницы: 8

Бренд: Rabid Elephant Страницы: 18

MTEK6000 Series

Бренд: Metretek Страницы: 81

SoundTrack LxT N/Forcer

Бренд: Larson Davis Страницы: 12

Бренд: Mark-10 Страницы: 26

Бренд: Dewetron Страницы: 24

Бренд: HBM Страницы: 84

Бренд: Solinst Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды