ABB TPS48-H33 Скачать руководство пользователя страница 50

Страница: 50 / 130

Operation Manual / 4 Product description / TPS44-H.. - TPS52-H..

Commissioning

Page 20 / 99

HZTL4037_EN

Revision A

August 2016

3.2

Inspection procedures

3.2.1

Introduction

Inspection procedures include preventative visual controls, monitoring and measuring work

before and during commissioning. Inspection procedures enable changes to the turbocharger

to be detected. Engine damage can be prevented.

3.2.2

Checks before commissioning

Filter mat (if available)



Check for damage and contamination.

Lubricating system

CAUTION

Contaminated oil
Serious damage to engine or property can be caused by dirt and solid mate-

rial particles in the oil.



At initial commissioning and after all service work, the complete lubricating

system must be thoroughly flushed with warm oil.



Use special running-in filters when running in the engine and after all ser-

vice work on the lubricating system.



Check that the oil filter is clean before commissioning.



Adhere to lubricating oil pressure at the inlet.



Adhere to lubricating oil temperature at the inlet.



For permissible values, see chapter

Monitoring operation [➙

23].

Warning plates



Check whether warning plates are present and legible.



Check whether the protective sheets have been removed.

Содержание TPS48-H33



































































































































Результаты поиска

Содержание TPS48-H33

Отзывы:

Похожие инструкции для TPS48-H33

Бренды по названию

Популярные бренды

ABB TPS48-H33, Руководство по эксплуатации

Результаты поиска

Содержание TPS48-H33

Отзывы:

Похожие инструкции для TPS48-H33

Бренды по названию

Популярные бренды