ABB TPS48-H33 Скачать руководство пользователя страница 63

Страница: 63 / 130

Operation Manual / 4 Product description / TPS44-H.. - TPS52-H..

Operation and service

Page 33 / 99

HZTL4037_EN

Revision A

August 2016

5.2.4

Service work according to data on the rating plate

(Usually after 8000 … 12000 operating hours)

WARNING

Incorrect handling of a cartridge group
Incorrect handling of a cartridge group can damage the turbocharger and

cause injuries to persons.



Have disassembly and assembly of the cartridge group carried out by an

ABB Turbocharging Service Station only.

NOTICE

Specialist knowledge of an ABB Turbocharging Service Station
Assembly and disassembly of the cartridge group and assessment of the ro-

tor and bearing parts requires the specialist knowledge of an ABB Turbo-

charging Service Station. The rotor parts turn very fast and are very sensitive

to unbalance.

The rotor and bearing parts must be checked and assessed by an ABB Turbocharging Service

Station. The following work can be carried out as preparation.



Remove turbocharger from engine (see chapter

Removing and Installing [➙

11]).



Dismantle the turbocharger and measure the clearances (see chapter Dismantling and

fitting [➙

59]).



Mechanically clean the nozzle ring, the turbine casing and compressor casing (see chapter

Periodic maintenance work [➙

39]).



Check the nozzle ring, turbine casing and compressor casing for cracks and ero-

sion/corrosion.

Содержание TPS48-H33



































































































































Результаты поиска

Содержание TPS48-H33

Отзывы:

Похожие инструкции для TPS48-H33

Бренды по названию

Популярные бренды

ABB TPS48-H33, Руководство по эксплуатации

Результаты поиска

Содержание TPS48-H33

Отзывы:

Похожие инструкции для TPS48-H33

Бренды по названию

Популярные бренды