ABB TOTALFLOW X G4 Series Скачать руководство пользователя страница 19

Страница: 19 / 20

⎦

Valve Control

: Valve Control option installed. Valve is in full

closed position.

↑

Valve Control

: Valve Control option installed. Valve is

opening (open signal is being sent to valve actuator).

↓

Valve Control

: Valve Control option installed. Valve is closing.

(Close signal is being sent to valve actuator).

Valve Control

: Valve Control option installed. Valve controller

override conditions met (DP/SP override set point or Low
Battery).

Valve Control

: Valve Control option installed. Local Lock-out

is initiated.

Measurement Applications

Back Flow Condition: Visible only when DP variable
displayed.

Zero Flow Condition: Visible only when Flow Rate displayed

Hold:

Displayed when PCCU32 is in

Calibration Mode

and

has a measurement application in

Hold

mode.

Alarm Condition:

Need to view alarm. You may need to

compare application limits to current values to determine
where the alarm condition is present.

A to D Failure:

Displayed if A to D Converter’s Differential

Pressure, Absolute Static Pressure or temperature readings
exceed maximum counts or are less than minimum counts.

The Display Does Not Scroll As Expected

When power is first applied, the unit should quickly go through startup

and begin cycling through the pre-programmed display items. If the

display does not scroll after startup, disconnect the main power and then

re-connect it. You should see something similar to:

Totalflow 32 Bit XFC

OS Part No. 2102900-001

If the display still doesn’t scroll, try disconnecting the power and re-

connecting it again. If still no success, do the following:

With PCCU32, connect to the unit and establish communications such as

Connect To Totalflow

Entry Mode

, etc. Go into

Terminal Mode

and type

“

0.0.0=COLD

” (Do not enter quotes). The unit should go through a

Cold

Start

procedure and begin scrolling. If this does not succeed, call the

number on the back of this guide and talk to a customer service

representative.

Содержание TOTALFLOW X G4 Series





















Результаты поиска

Содержание TOTALFLOW X G4 Series

Отзывы:

Похожие инструкции для TOTALFLOW X G4 Series

Бренды по названию

Популярные бренды

ABB TOTALFLOW X G4 Series, Руководство для стартапов

Результаты поиска

Содержание TOTALFLOW X G4 Series

Отзывы:

Похожие инструкции для TOTALFLOW X G4 Series

Бренды по названию

Популярные бренды