ABB TOTALFLOW X G4 Series Скачать руководство пользователя страница 18

Страница: 18 / 20

Table 2.

Alarm & Status–Codes and Description

Alarm/Status

Codes

Description

I/O Subsystem

Low Lithium Battery Alarm

: When

(low lithium) is displayed;

lithium battery voltage is below 2.5 VDC. A new lithium battery
measures approximately 3.6 VDC.

Low Charger:

Displayed if the battery charging voltage is less

than 0.4 VDC greater than the battery voltage.

Communications

→

Transmitting Data:

←

Receiving Data:

Nak

. Negative Acknowledgement w/packet list.

Ack

. Positive Acknowledge of receipt of request.

Waiting for Ack

. Waiting for response after transmission.

Exception Alarm Processing.

ID Recognized.

Listen Cycle

. Flashes if this remote port is active and running

Totalflow Remote Protocol. Flashes in sync with listening
cycle that occurs at 1, 2 or 4 second intervals.

MODBUS ASCII

: Modbus ASCII protocol is selected for this

port.

MODBUS RTU

: Modbus RTU protocol is selected for this

port.

Local Protocol:

Displayed when PCCU32 port is active and

running

Totalflow Local

Protocol.

Packet Protocol:

Totalflow Packet Protocol is active on this

port.

LevelMaster Protocol

: LevelMaster protocol is selected for

this port.

Valve Control

Valve Control

: Displayed when the Valve Control option is

installed and no other Valve Control symbols are valid.

Valve Control

: Valve Control option installed. Process Value

(PV) is within the user set dead band. No control action
required.

⎡

Valve Control

: Valve Control option installed. Valve is in full

open position.

Содержание TOTALFLOW X G4 Series





















Результаты поиска

Содержание TOTALFLOW X G4 Series

Отзывы:

Похожие инструкции для TOTALFLOW X G4 Series

Бренды по названию

Популярные бренды

ABB TOTALFLOW X G4 Series, Руководство для стартапов

Результаты поиска

Содержание TOTALFLOW X G4 Series

Отзывы:

Похожие инструкции для TOTALFLOW X G4 Series

Бренды по названию

Популярные бренды