background image

  

Complete Solutions in Emergency Lighting   

 

 

      

     STANILITE

  

Complete Solutions in Emergency Lighting   

 

 

      

     STANILITE

© Thomas & Betts (Australasia) Pty. Ltd. 2016

   

 

 

                      

                 

Rev: 2.0     24 February 2016     4

© Thomas & Betts (Australasia) Pty. Ltd. 2016

   

 

 

                      

                 

Rev: 2.0     24 February 2016     1

Thomas & Betts (Australasia) Pty. Ltd.  ABN: 062 074 810 898

Head Office: Unit D3, 3-29 Birnie Avenue, Lidcombe NSW 2141, Australia

Manufacturing: 23a Nyrang Street, Lidcombe NSW 2141, Australia

Phone: 1300 666 595  Fax: 1300 666 594  Email: [email protected]  Website: www.tnbaust.com

LED Quickfit Vandal Resistant Jumbo Exit

Installation Manual

Standard, Nexus LX, Nexus RF

TROUBLE SHOOTING GUIDE

If you have installed and connected the unit as per the instructions listed earlier and it does not function correctly, use the following table 

as a guide to fixing the problem. Look up the type of fault in the left column and check the possible causes from the right column.

If the unit still does not work after checking these possible causes, contact Thomas & Betts Service in Australia on 1300 666 595, Monday  

to Friday, 8.30am to 4.30pm (AEST) and ask for help. Our trained service personnel will usually be able to take your call immediately and 

assist you in resolving your difficulty. Thomas & Betts is committed to providing valuable Through-Life Support for its products. 

Doc No: 29-99569

GREETINGS

Congratulations on choosing to use this Thomas & Betts product covered by our unique Through-Life Support system. This document is 

designed to assist you during the installation of this product; for the safety of yourself and others 

Thomas & Betts recommends 

that  you  read  this  document  thoroughly  before  commencing  installation.

 The  fittings  are  designed  for  easy 

installation. They are advanced pieces of electronic equipment which, when treated with care and maintained through regular and 

appropriate servicing, will perform reliably for many years to come.

SAFETY WARNING

In Australia and New Zealand, only licensed electricians are permitted by law to work with 240 Volt electrical installations.

Do not attempt to install or connect this product unless you are a licensed electrician.

Turn off and isolate the electrical supply before connecting this fitting to the building wires.

Do not touch the terminals of the terminal block when the light fitting is energised.

The only user-serviceable parts are fluorescent or halogen lamp/s. LED light sources are not user-servicable.

Do not tamper with the fitting or the warranty will be void.

As the installer, it is your responsibility to ensure compliance with all relevant building and safety codes, (ie: AS3000, AS/NZS2293).  

Refer to the applicable standards for data and mains cabling installation procedures and requirements.

Important Note: This product is designed for indoor use only.

NEXUS LX (DATA CABLE SYSTEM)

The Nexus range of emergency light fitting are designed to be connected together into a special communication network over a Level 

4 (or higher) high speed, single twisted pair data cable. The Nexus LX User & Technical Guide describes all you need to know to 

successfully install a Nexus project. Ask for it from your supervisor, from your employer or from your nearest Thomas & Betts product 

supplier. The network cabling of the building must be installed as per the procedure detailed in the Nexus LX User & Technical Guide. No 

mains or mains carrying cables are to be connected to the data terminals or cables.

NEXUS RF (WIRELESS SYSTEM)

The Nexus RF range of light fittings are designed to communicate via a proprietary RF network, however the electrical installation of the 

fittings is identical to that of a standard non-monitored fitting.

#

Fault

Possible Causes

1

Lamp and LED not lit

AC mains supply not connected; or

AC mains supply turned off; or

Unit not inserted into the base properly; or

Test switch damaged

2

Lamp not lit but LED is lit

Lamp damaged; or

Lamp incorrectly inserted

3

Lamp is lit but LED not lit

Test switch damaged; or

Battery not connected

4

The lamp does not switch to emergency mode when the 

test button is pressed

Test switch damaged

5

The lamp works momentarily on emergency when the test 

button is pressed

Battery not yet charged (allow up to 16 hours)

This Document Covers

What’s Inside the box

Safety Warning

Main Frame

Installation Instructions

Diffusers

Removal Instructions

Ceiling Bracket

Testing Precautions

Hole Plug Set (6 Pieces)

Trouble Shooting Guide

Installation Manual
Warranty Information

Отзывы: