ABB Terra 94 Скачать руководство пользователя

Страница: 33 / 54

5.7

Prepare for commissioning

Danger:

Hazardous voltage

•

Do not commission the EVSE. Only a service engineer of the

manufacturer is qualified to commission the EVSE.

1. Tell the owner that the EVSE is ready for commissioning.

2. Make sure that the site agrees with these requirements:

•

The EVSE is installed.

•

AC input power is available from the grid provider.

•

You are present during the commissioning, for assistance and to energize

the power to the EVSE on the power distribution board.

•

Internet access is available, through 2G/3G/4G or through a wired Ethernet

connection.

•

An EV must be available with a compatible connection. If the EVSE has more

than one connection type, an EV of each type must be available.

•

The site operator or owner is available to receive instructions from the

service engineer of the manufacturer.

3. Make sure that these data are available:

•

Contact data of the contact person on site

•

Address of the EVSE

•

Site name

•

Exact location of the EVSE: longitude and latitude. If there are more EVSEs

on one location, make sure that the coordinates are slightly different (at

least 0.0001 degree) so that the EVSEs are not at the same location on the

map.

•

Specification of the external fuse at the power distribution board

•

Date that the installation is done

•

Special remarks, for example to decline the authorization for the service

engineer of the manufacturer to take photos

•

Photo of the surroundings of the EVSE

Installation

BCM.S1102.0-EN | 001

Содержание Terra 94






















































Результаты поиска

Содержание Terra 94

Отзывы:

Похожие инструкции для Terra 94

Бренды по названию

Популярные бренды

ABB Terra 94, Руководство по установке

Результаты поиска

Содержание Terra 94

Отзывы:

Похожие инструкции для Terra 94

Бренды по названию

Популярные бренды