ABB REPL-01 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 87

background image

Mechanical installation

19

Mechanical installation

What this chapter contains

This chapter contains placing and mounting instructions for the
module.

WARNING!

Follow the safety instructions given in this manual and

in the appropriate drive hardware manual

.

Mounting

The REPL-01 module is to be inserted into its specific position in
the drive. The module is held in place with plastic retaining clips
and two screws. The screws also provide the earthing of the
CAT 5 STP cable shield connected to the module, and
interconnect the GND signals of the module and the control board
of the drive.

On installation of the module, the signal and power connection to
the drive is automatically made through a 34-pin connector.

Mounting procedure:

• Insert the module carefully into its position inside the drive until

the retaining clips lock the module into position.

• Fasten the two screws (included) to the stand-offs.

Note:

Correct installation of the screws is essential for fulfilling the

EMC requirements and for proper operation of the module.

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

«
...
23
24
25
26
27
...
»

Содержание REPL-01
























































































Отзывы:

Нет отзывов

Похожие инструкции для REPL-01

Бренд: Panasonic Страницы: 8

Бренд: Linksys Страницы: 2

Бренд: Dynex Страницы: 12

QuattroPlus 1400557

Бренд: Mobeli Страницы: 4

Бренд: Belkin Страницы: 18

Бренд: Belkin Страницы: 1

68VHDCI-50F SSR 8

Бренд: National Instruments Страницы: 4

Smart connect KNX Hue

Бренд: ISE Страницы: 2

VERDEdri 17-10504K

Бренд: World Dryer Страницы: 8

Бренд: Bebob Страницы: 3

Бренд: Wyze Страницы: 4

Бренд: Lindy Страницы: 8

Бренд: KTI Networks Страницы: 24

Бренд: Panasonic Страницы: 6

Бренд: Panasonic Страницы: 12

AKHTF900 - INTERFACE ADAPTOR

Бренд: Panasonic Страницы: 12

Бренд: Panasonic Страницы: 14

Бренд: Panasonic Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды